Replacement Grease Seal Recommendation for Dexter Hub 8-219

Question

Question:

Looking for seal TCM 21334TB that can out of a Dexter 8-219 Hub/Brake or a kit that contains 14125A/14276 and 25580/25520 bearing/race kit

asked by: Justin T

0

Expert Reply:

For your Dexter hub part number 8-219 the correct seal is the part # GS-2125DL as we carry that hub as part # 8-219-4UC3 and that's what comes with it.

expert reply by: Jameson C

0

Answer 1

Hey Vic, thanks for reaching out. We will have the seal you need, but these Dexter 7K D70 axles are tricky because Dexter used two different seal sizes on their 7K axles and the info on the sticker actually doesn't tell us what seal it uses.…

view full answer...

Answer 2

The highest quality grease we carry for wheel bearing is the LMX red grease like the part #L11390. LMX Red is heavy-duty, premium grease for the toughest lubricating jobs on the biggest, heaviest equipment. It performs better under higher pressures…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Replacement Grease Seal Recommendation for Dexter Hub 8-219

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching