Westin Sportsman Grille Guard Mounting Brackets for a 2006 Chevy Silverado 1500

Question

Question:

I have a 2006 Chevy 1500 looking for mounting hardware for brush guard

asked by: Brian M

0

Expert Reply:

Both the grille guard and mounting bracket will be specific to the vehicle. For example, a grille guard off of a 2002 Chevy S-10 can not used on a 2003 Dodge Dakota even with the correct mounting brackets. Therefore, as long as the Westin grille guard you have is designed to fit a 2006 Chevy Silverado 1500 then the correct replacement mounting brackets for the Westin Sportsman Grille Guard part # 40-1175 is the Replacement Mounting Kit for Sportsman Grille part # 40-117PK.

expert reply by: Conner L

0

Answer 1

Hey David, thank you for the photos and explanation! That is most definitely an Aries Grille Guard, and if it came off of a 2006 Chevy Silverado 1500 then we're looking at the part #AA4059-2 which will also fit your 2003 model by using the…

view full answer...

Answer 2

I can tell you that the brackets for the Westin Sportsman #40-1245 which is a fit for your 2006 Chevrolet Silverado 2500HD are part #40-124PK. This will get the grille guard on your truck for sure. I have no way of knowing if the other brackets you…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

No long-term contract, Natalie - but a service plan is required to use the trackers. When you buy the 3000 with wifi assist #PM84FR, 5000 #PM64FR, or 5000 with wifi assist #PM74FR from etrailer, you’re purchasing the hardware/device only. To activate…

view full answer...

Answer 6

Hello Dustin, To mount the TecNiq Mini Side Marker Light - Amber - 3/4" - Grommet Mount - 9" Wire #TN22XR, you’ll need to drill a 3/4-inch diameter hole. The rubber grommet is designed to press-fit into this standard hole size, allowing the…

view full answer...

Answer 7

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 8

Hi Tony! When using a 14" wheels with the etrailer Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized #AKIHUB-545-35-G-EZ-K, you will want to torque the lug nuts to 75 to 85 foot pounds. And those goes for steel or…

view full answer...

Answer 9

Hi Mark, it looks like you picked up the Curt hitch that fits the cab and chassis models of the 1977 Ford trucks. Do you know if your truck was originally built as a cab and chassis model which means it came with a slightly wider frame and was made…

view full answer...

Answer 10

Use Hopkins part #HM47425. It's an adapter that plugs in to your round 7-way and gives you a 7-blade RV style connector.

view full answer...

Answer 11

Hey Mark, so the Curt hitch part #C15302 basically is strong enough without attaching to the bumper so it wasn't designed into it. Curt is very thorough with their hitch designs so I would not worry about this hitch not having the needed…

view full answer...

Answer 12

I reached out to my contact at Demco and he said that depending on the year, there was a gear adjustment bolt on the cab side of the base of the older Hijacker models. He also said some of the slide bar heads had an adjustment bolt there as well for…

view full answer...