Can the P3 Brake Controller Mount Vertically

Question

Question:

can I mount my P3 vertically as long as it is horizonally in line with direction of travel? Thanks

asked by: Billy P

0

Expert Reply:

I attached two pictures that show how the P3 part # 90195 can be mounted. As long as it is squarely facing the rear of the vehicle and level side to side the controller can be totally vertical.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Good morning Brett, Yes, the Curt Spectrum Brake Controller w/ Custom Harness - Dash Mounted Knob #C28SV and the Curt Echo Under-Dash Bluetooth Brake Controller w/ Custom Harness #C46GV will both work just fine in your 2026 Ram 1500 Rebel. They are…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 7

Hi there Chris, great question. Yes the Redarc #RED87CR is truly a plug and play brake controller for your 2026 Ram 1500. It connects directly to the factory tow controller connector under the dash, so there’s no dealer programming required like you…

view full answer...

Answer 8

Hey Beverly. The Replacement Mounting Hardware Kit for Westin HDX Grille Guard with Punch Plate item #W67FR is the correct one for your 2019 Ram 1500. It'll have all the brackets, bolts, washers, and nuts you'll need. The item #W67FR is the…

view full answer...

Answer 9

Hey Dylan, thanks for reaching out. We do carry that 15" aluminum Liger wheel in black. We have them in both a 5-lug and 6-lug. Take a look at the following: - Aluminum Liger Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - Glossy Black…

view full answer...

Answer 10

The Air Lift LoadLifter 5000 Ultimate Air Springs with Internal Bumpers part #AL88375 are a fit for a 2019 Ram 1500 Rebel. You can add the Plus Upgrade Kit #AL52301 to get the stainless components.

view full answer...

Answer 11

Hi Jeff! To be perfectly honest, there is no difference between them. The Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness #RED72CR comes to us already put together to fit your 2017 Toyota Tacoma, whereas the Redarc Tow-Pro Liberty Brake…

view full answer...

Answer 12

Hi James! With your GVWR being 7,600 pounds, your loaded tongue weight should be around 760 pounds. With that said, I recommend going with the Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 8.5K GTW, 850 lbs TW…

view full answer...

Can the P3 Brake Controller Mount Vertically

Continue Researching