Troubleshooting Warning Power Overload On Tekonsha Prodigy P3 Brake Controller
Updated 08/08/2017 | Published 08/06/2017
Question:
My son replaced my old receiver on my truck now my brake controller is flashing a power over load message. I can not access the on board diagnostics. I cant figure out where to look for the problem. Have checked power at the source, at the receiver plug in, and the trailer. Have any Ideas?
asked by: Sherri
Expert Reply:
Your Tekonsha Prodigy P3 Trailer Brake Controller # 90195 when flashing Warning! Overload No Brakes, is detecting an excessive current overload condition during operation according to the installation details I've attached. This means there is a short somewhere on the brake output circuit on either the truck or the trailer.
Start by examining the trailer connector. Make sure that the pins on the vehicle side of the connection and the sockets on the trailer side are not damaged, bent, or corroded. If you can see green corrosion on the pins or the sockets, there is a possibility that the corrosion may have spread to the interior of the connector itself, causing a short.
Then trace the output circuit back from the connector all the way to the trailer brake magnets. Check the brake output wire (usually a blue wire) for pinch points or worn or cracked insulation. If at any point in the circuit there is copper conductor wire showing, it can possibly short out on the trailer frame.
You will also want to examine your brake magnets and their connections. Make sure that the ground connection for each magnet is securely attached to the trailer frame. Check that the brake magnets are not excessively worn. If you pull the brake drum off and can see the copper windings through the face of the magnet, it is time to replace them. I've attached an article on how to test your magnets.
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: slipper spring hangers
- Search Results: spring hangers
- Shop: Brake Controller
- Shop: Single-Axle Trailer Hanger Kit for 1-3/4" Slipper Springs - 1-1/2" Tall Front
- Q&A: Diagnosing Overload Warning, No Brakes, On a Tekonsha Prodigy P3 Brake Controller
- Article: Troubleshooting Brake Controller Installations
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Q&A: Wiring Diagram and Instructions for a Tekonsha Prodigy P3 Brake Controller
- Q&A: How Many Volts Should a Brake Controller Put Out on the Highest Gain
- Shop: Hydrastar Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Shop: Dexter DX Series Electric Over Hydraulic Brake Actuator for Disc Brakes - 1,600 psi
- Q&A: Wiring Diagrams for Hydrastar Electric Over Hydraulic Trailer Brake Actuators
- Video: The Low-Down on the Vesper Steel Modular Trailer Wheel
- Q&A: Recommended 15 Black Wheels With A 5-On-5 Bolt Pattern
- Article: Trailer Wiring Diagrams
- Article: Testing Trailer Brake Magnets for Proper Function
- Q&A: Tekonsha P3 Brake Controller 90195 Displays Message Output Shorted No Brakes
- Q&A: Best Brake Controller for a 2006 Chevy Silverado 2500HD
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: How to Choose a Trailer Brake Controller
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Search Results: trailer wiring
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
on Trailer Brake Controller
