Installation Torque Specs For Andersen Ultimate Connection

Question

Question:

What are the bolt torque settings

asked by: Dave L

0

Expert Reply:

The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter - 20,000 lbs # AM3200 only has 4 set screws that require torque. According to the installation details from the manufacturer, the 4 set screws need to be tightened to 40 ft. lbs. of torque using a 1/4 inch allen wrench. I've attached the installation details for you which state to tighten the other bolts snug.

expert reply by: Jason S

0

Answer 1

In regards to the Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter part #AM3200, the four kingpin coupler set screws will need to be torqued to 40 ft. lbs. per the manual. The kingpin coupler will need to be center on the pin…

view full answer...

Answer 2

Hey Ronald, To get you swapped over to a motorized step I would need know the distance from the ground up to the mounting space for the steps and the width of the mounting space in order to pick out the correct fit. I've attached some pictures…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Installation Torque Specs For Andersen Ultimate Connection

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching