Which Edge CS2 Programmer Fits 2014 Chevy Silverado 1500 with 5.3 liter Engine

Question

Question:

I was looking for a way to ask a question in the expert Questions area but couldnt find so asking here. Will the edge ct tuner 85150 work well with a 2014 chevrolet silverado 5.3 liter

asked by: Bruce

0

Expert Reply:

The correct Edge CS2 programmer you would need for your 2014 Chevy Silverado 1500 is the part # EP85350 which can give you up to 18 horsepower and 27 ft lbs of torque.

expert reply by: Jameson C

0

Answer 1

The connection point for the 2013 Lincoln Navigator is under the instrument panel above the brake pedal. I have attached an image to better help you see where it is located. The custom fit wiring harness for your 2013 Lincoln Navigator is dependent…

view full answer...

Answer 2

It seems like you may have the incorrect wiring connector and the harness in the photo is not the correct fit. For your 2015 Lincoln Navigator, the correct wiring adapter is #22292 for your Tekonsha Prodigy P3 #90195. If you have the factory 7-way or…

view full answer...

Answer 3

Hi Jim; it can be hard to tell but the #RED67CR does include the custom wiring harness for your 2017 Lincoln Navigator. This will allow for a plug and play installation using your factory tow port.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Which Edge CS2 Programmer Fits 2014 Chevy Silverado 1500 with 5.3 liter Engine

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching