Is there a Brake Mounting Flange that Has a 3 Inch Diameter Center Hole

Question

Question:

I need a 3inch center hole, 5 bolt flange that goes ON a 3inch axle. I can not use a 2.75inch flange that goes on the spindle at the end of the axle. What does eTrailer have for me?

asked by: Michael

0

Expert Reply:

We have a 4-bolt brake mounting flange # 4-50 which has an inner diameter of 3.01 inches. This particular flange is meant for 12-1/4 inch brake assemblies usually found on 8K axles which are usually 3-1/2 inches in diameter.

expert reply by: Michael H

0

Answer 1

The Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3,500 lbs #AKEBRK-35 will bolt onto the standard brake flange like #4-35 that is 2-7/8 inches on center and 4 inches diagonal on center. I've attached a photo to assist.…

view full answer...

Answer 2

You will need to measure to select the correct brake assemblies for your axles. You need to know that the brake assembly is compatible with the brake mounting flange and with the drum's diameter and depth. I added a photo showing how to measure a…

view full answer...

Answer 3

The left side is the driver side, right side is passenger side. On a trailer brake assembly like #23-105 the arm that the magnet is on points to the front of the trailer and the magnet always will be on the bottom. I have included a picture that…

view full answer...

Answer 4

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 5

The braking performance will not be very good if you install brake assemblies on the wrong side of the trailer. The left side assembly is the driver's side (if the trailer were a car) and the right side is the passenger's side. The actuating…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Is there a Brake Mounting Flange that Has a 3 Inch Diameter Center Hole

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching