LED Trailer Light Replacement Recommendation for 2005 Featherlite Model 8546 Gooseneck Trailer

Question

Question:

I would like to upgrade the single led brake lights to brighter multi leds.

asked by: Jason L

0

Expert Reply:

Based on the picture you submitted it looks like you are looking for the part # STL22RB which is an LED version of the light you have that has 12 light emitting diodes.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For a black bracket/harness to use with the GloLight Thinline LED Trailer Clearance or Side Marker Light #MCL165AB you'd want the part #A65PB or for a chrome one you'd want the part #A67CB.

view full answer...

Answer 2

The Black Molded ABS Mounting Bracket for Thinline Series Clearance Lights, #A65B, are compatible with the Optronics GloLight Thinline Lenses, #MCL165RB. The mounting brackets will allow you to mount on standard 3 inch centers and the overall…

view full answer...

Answer 3

If you have already added the fuse and the trailer charge circuit is not activated in the 2019 Ford F-350 Super Duty with factory integrated brake controller, then you want to make sure the trailer is connected and you press the brake according to a…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

LED Trailer Light Replacement Recommendation for 2005 Featherlite Model 8546 Gooseneck Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching