Replacement Parts for Yakima 1A Raingutter Roof Rack Towers

Question

Question:

I have the a1 towers with the extenders that I woukd like to convert back to the non-extended version but I lost the original spacers. Can I get just the original spacers thru you?

asked by: Andrew M

0

Expert Reply:

It sounds like you are talking about the shear block bases # Y8810007 for the Raingutter towers such as # Y8810137. This is a set of 4.

Other replacement parts for the Yakima Raingutter 1A towers include:
Boot set # Y8810008
Another shear block set # Y8810006
Hardware kit # Y8810136

expert reply by: Michael H

0

Answer 1

Yakima refers to the part you're needing as a clip spacer for their 1A RainGutter Towers, part #Y00101. The replacement plastic clip spacers aren't available individually, they are included in the #Y8810136 replacement hardware bag, so…

view full answer...

Answer 2

We have a few options for replacement pads for Yakima roof racks like item #Y8810008. They are organized by what specific tower they go to. I have linked our entire selection below. If you would like to email me back some information on yours like a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

It sure is Pete and welcome back! Our Replacement Fabric for etrailer Powered RV Awning item #e86QV is a compatible replacement for your Dometic Power Awning so long as it's 20' wide. The fabric on all those awnings installs the same way. The…

view full answer...

Answer 8

Hey Kevin. Our Replacement Fabric for etrailer Powered RV Awning item #e86QV is just the replacement fabric. It'll attach to your existing awning roller so long as you have a 20' powered awning. There is no stitching built into the fabric for…

view full answer...

Answer 9

Yes, they will Jeff. The etrailer Hitch item #e77ZV fits both the 2025 and 2026 Toyota Camrys. This is a class I hitch with a 1-1/4" receiver that has a 2,000 lbs towing capacity and a maximum tongue weight of 200 lbs. If you're needing a…

view full answer...

Answer 10

Hey Zach, this is a really great question that I don't have a super exact answer for but I can still help. So our hitch manufacturers will basically make a hitch for any vehicle there is a demand for one. Including your 2025 Toyota Camry with the…

view full answer...

Answer 11

Hi Ann, It is not possible to put a 2 inch hitch receiver on your 2025 Toyota Camry. The only size hitch for this vehicle has a 1-1/4 inch receiver, the Curt Trailer Hitch Receiver #C94RV.

view full answer...

Replacement Parts for Yakima 1A Raingutter Roof Rack Towers

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching