Is There Wiring Harness Needed to Install Brake Controller in 2011 Chevy Silverado 1500

Question

Question:

What wiring harness do I need for a Chevrolet Silverado 1500 Z-71 ?

asked by: David

0

Expert Reply:

When installing a brake controller like the # 80550 in your 2011 Chevy Silverado no plug is present under the dash, but the needed wires are already run. You will connect the brake controller wiring with the vehicle wiring already present under the dash.

I attached an install video and help article for you to check out that show how this is done.

expert reply by: Jameson C

0

Answer 1

Tom, unfortunately the controller 2020003067 is not going to work in place of the 289252, so It would need to be replaced with the 289252. I have also confirmed this with Lippert to make sure.

view full answer...

Answer 2

In 2007, Chevrolet stopped offering plug-in connectors for brake controllers on their full size trucks with tow packages. Instead, you will have four or five blunt-cut wires bundled underneath your dash. The wire colors should be red with a black…

view full answer...

Answer 3

Modern trailer wiring kits like the part #TK33VR which fits your 2022 Ford Bronco if it does not have LED taillights or the part #TK99VR if you do have them do require running a power wire up to the battery to draw power from for the trailer's…

view full answer...

Answer 4

This is entirely possible, in fact it's been done so often we have a Technical Bulletin provided by Tekonsha showing exactly how to do this (see link). Let's start with an aftermarket brake controller. The Tekonsha P3 you'd looked at,…

view full answer...

Answer 5

On the 2011 Chevrolet Silverado Z71, the wiring for the brake controller is already ran and bundled underneath the dashboard on the driver side. This wiring may be taped together and tucked up and out of the way. There is not a plug-in wiring harness…

view full answer...

Answer 6

Sure, you can move your original Prodigy brake controller from the 2004 Ford F-150 to the 2011 Chevrolet Silverado with factory tow package, with no problems. If you installed your Prodigy brake controller with a brake controller wiring harness,…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Is There Wiring Harness Needed to Install Brake Controller in 2011 Chevy Silverado 1500

Featured Help Information

Miscellaneous Media

Continue Researching