What is the Mounting Hole Spacing on Titan Zinc-Plated Brake Actuator T4747220

Question

Question:

I am wondering if the two larger holes for the 5/8 in bolts that connect T4747220 onto the trailer are 5 inches apart. That would match the existing pattern on my EZ loader trailer that I am upgrading.

asked by: Hugh A

0

Expert Reply:

I went out to the warehouse and measured the bolt holes on actuator # T4747220. The 2 larger holes are spaced 5 inches apart on center. I have included a picture showing this and other measurements for you.

expert reply by: Michael H

0

click to enlarge

John R.

8/4/2024

How many of the 5 holes need bolts in them for mounting. Is it possible to use only the two holes spaced at 3" or maybe just maybe thise two plus the last one

Jerred H.

8/5/2024

@JohnR 2 or 3 depending on the bolt size you want to use. I checked the instructions you can install the Dexter Actuator item # T4747220 using all 3 of the small bolt holes or just 2 of the larger holes. Anything else and you won't get the full 8,000 lbs capacity.

Answer 1

We do have actuators that will work with a trailer that has disc brakes and an 8,000 lb GTW. The Titan #T4747200 may be a great option depending on the hitch ball size you need. It works with a 2-5/16" hitch ball, bolts onto 3" wide channel…

view full answer...

Answer 2

You will need to cut that off of your 2001 Cobalt 240 to replace the actuator since there are no replacements that will fit. I recommend welding on a straight tongue so you can use a bolt-on actuator like the Dexter Zinc-Plated Brake Actuator…

view full answer...

Answer 3

The Titan 8K Surge Coupler #T4747220 should be installed using all 3 of the smaller mounting holes or both of the larger holes (using hardware with dimensions that match) to secure it to the trailer's 3-inch-wide tongue.

view full answer...

Answer 4

The DA91 Demco surge brake actuator that you are looking for is part #DM8750311. This has a 2-5/16" coupler, comes with an electric lockout, is designed for disc brakes, and has a weight capacity of 8,000 lbs towing and 800 lbs tongue weight.

view full answer...

Answer 5

The bolt hole dimensions of the Demco Brake Actuator #DM8669112 are 12-1/2 inches on center and 3 inches on center. I've attached a photo to assist. The Titan #T4747220 has mounting holes that are 3 inch on center so 2 of the 3 holes will align…

view full answer...

Answer 6

I attached a picture that shows all of the mounting hole dimensions pointed out as well as a second picture that shows the distance from the front mounting hole to rear of shroud on the Demco DA91 #DM8750311 you referenced.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What is the Mounting Hole Spacing on Titan Zinc-Plated Brake Actuator T4747220

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching