What Are the Highest Weight Capacity Dexter Brake Assemblies That Have the Integrated Parking Brake

Question

Question:

hello are the 6K the highest rated brakes that Dexter has with an integrated parking brake?

asked by: Parker

0

Expert Reply:

The Dexter 6,000 lbs brake assemblies # 23-113 and # 23-112 are the highest rated weight capacity assemblies that we carry that have the integrated parking brake.

expert reply by: Jared P

0

Answer 1

Dexter trailer brake assemblies #23-113 and #23-112 have a bracket, see picture, that you would attach a cable to. At the other end of the cable is a lever. When you pull the lever it pulls the cable that pulls the bracket and pushes the shoes out to…

view full answer...

Answer 2

Dexter left and right 12 x 2 electric drum brakes #23-112 and #23-113 include a parking brake and are rated for 6K axles. These use a brake flange with a 5-bolt mounting pattern; if you don't have these already they will need to be welded in…

view full answer...

Answer 3

We've checked in the past and found that the M1102 trailer that you have has a hub that has bearings #14125A and #25580 which matches hubs like the #42866UC3-EZ which has an 8 lug bolt pattern. There isn't a hub that would fit that has the 5…

view full answer...

Answer 4

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What Are the Highest Weight Capacity Dexter Brake Assemblies That Have the Integrated Parking Brake

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching