Part Number for Dutton-Lainson Hand Winch

Question

Question:

I am looking for a winch for cable that ties my boat dock to land i am replacing a shelby 5405 .and had decided on a DL1402A. i did not find that model on your site, but the DL15303 appears similar. can you tell me the difference?

asked by: Ronald K

0

Expert Reply:

The product ID for the DL1402A is the Dutton-Lainson Hand Winch with TUFFPLATE is # DL15303.

expert reply by: Charles S

0

Answer 1

Yes the Dutton Lainson Hand Winch part #DL15303 that you referenced will work great in place of your older DL winch. It uses same bolt pattern and everything so the install will be simple.

view full answer...

Answer 2

I have a replacement winch option for you, but unfortunately your Dutton-Lainson DL1402 not having the A means it was made between 1991-1999. Unfortunately the rebuild kit for these older winches was discontinued a while back. The only option would…

view full answer...

Answer 3

The Dutton Lainson winch part #DL15303 was designed to be used with a 1/4 inch diameter wire rope like the Dutton Lainson Wire Rope #DL24100.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Part Number for Dutton-Lainson Hand Winch

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching