Will Dutton Lainson Hand Winch DL15303 Replace DL1400

Question

Question:

Looking to order DL15303 to replace a DL1400 manufactured in 1987. Is this a comparable and suitable replacement.

asked by: Ed D

1

Helpful Expert Reply:

Yes the Dutton Lainson Hand Winch part # DL15303 that you referenced will work great in place of your older DL winch. It uses same bolt pattern and everything so the install will be simple.

expert reply by: Jameson C

1

Answer 1

The product ID for the DL1402A is the Dutton-Lainson Hand Winch with TUFFPLATE is #DL15303.

view full answer...

Answer 2

I have a replacement winch option for you, but unfortunately your Dutton-Lainson DL1402 not having the A means it was made between 1991-1999. Unfortunately the rebuild kit for these older winches was discontinued a while back. The only option would…

view full answer...

Answer 3

The Dutton Lainson winch part #DL15303 was designed to be used with a 1/4 inch diameter wire rope like the Dutton Lainson Wire Rope #DL24100.

view full answer...

Answer 4

Shelby is no longer in business and would not be the same as Fulton; there are no ratchet repair kits available for Shelby so you'll need to replace your winch. Keeping in mind that a boat trailer winch has a boat-size-to-winch capacity that is…

view full answer...

Answer 5

I do have an option but Shelby Trailer Products went out of business years ago so replacement parts are just not an option. Therefore, you will need to cut the old coupler off and then bolt-on a new one for which I recommend the Channel Tongue…

view full answer...

Answer 6

The Dutton-Lainson Hand Winch part #DL15303 is the replacement that I recommend for your Shelby Hand Winch 5405. These winches both have the same 1,400 lb capacity and overall size. In regards to mounting, most hand winches now use a standard pattern…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will Dutton Lainson Hand Winch DL15303 Replace DL1400

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching