Spring-Center-To-Spring-Center Length Of Dexter Trailer Axle Beam T3584F-EZ-8974

Question

Question:

What is the distance between the spring centers?

asked by: Edward J

0

Expert Reply:

The distance from spring-center-to-spring-center of the Dexter Trailer Axle Beam, part # T3584F-EZ-8974 is 74-inches.

This axle is designed with a weight capacity of 3,500-lbs and the hub-face-to-hub-face measuresment is 89-inches. I have attached a drawing that shows these dimensions you can check out.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hey George! I do have brakes made specifically for your Demco KK260 Kar Kaddy! Demco Hydraulic Drum Brake - Single Servo - Galvanized - 10" - LH - Self-Adjusting - 3,500 lbs #DMSB24429M and Demco Hydraulic Drum Brake - Single Servo - Galvanized…

view full answer...

Answer 10

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 11

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Spring-Center-To-Spring-Center Length Of Dexter Trailer Axle Beam T3584F-EZ-8974

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching