Trailer Running Light Fuse Location 2016 Ram 3500

Question

Question:

I have a Dodge 2016 3500 Dooley my problem is with the running lights on the trailer Im looking for the fuse in the truck I cannot find the location for the fuse the running lights on the truck work but not on the trailer

asked by: Thomas G

0

Expert Reply:

I pulled up a copy of your owners manual online and it looks like F29 is the fuse slot you are looking for for the trailer running lights circuit. This will be a blue 20 amp cartridge fuse.

expert reply by: Jameson C

0

Answer 1

Unfortunately that is typical issue on a Ram 3500. There are many forums that talk about this. There is a fuse that you should check F30 that sometimes causes this issue. Next use a circuit tester like #PTW2993 to test the 5 o'clock pin which…

view full answer...

Answer 2

To install an aftermarket brake controller like the Prodigy P3 part #90195 on a 2016 Dodge Ram that has the factory integrated controller you will have to disconnect the ITBM (Integrated Trailer Brake Module). Doing so will turn on a warning lamp on…

view full answer...

Answer 3

There are a lot of possibilities here so I will try to help you narrow it down. Start at the 7-way on your 2016 Ram 5500. Using a circuit tester like #PTW2993 check for power on the brake output pin while using the manual override on your brake…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Trailer Running Light Fuse Location 2016 Ram 3500

Continue Researching