Availability of Dual Ball Mount that Fits 3 inch Hitch on Ford Truck

Question

Question:

i checked it takes two sleves to make it a 2 in and one sleve to make it a 2.5 in you do not carry any looking receviers or any way to get one it needs to be adjustable to also thanks

asked by: John R

0

Expert Reply:

Sounds like you do have a 3 inch trailer hitch on your Ford truck. The one dual-ball mount we offer for a 3 inch hitch is the part # ED30OFFSET. This has a 2-5/16 and 2 inch hitch ball on either side and offers up to 6 inches of rise or drop.

expert reply by: Jameson C

0

Answer 1

Hey Kody! I found an extremely detailed schematic diagram of the BulletProof Hitches 2-Ball Mount for 3" Hitch item #ED304 that I have attached below. It covers multiple dimensions of that hitch pin hole to the angled piece. If you have any…

view full answer...

Answer 2

Hi Tommy; that's correct there isn't a 3-ball ball mount for a 3 inch hitch with exactly a 5 inch drop. The closest is a 4-1/2 inch drop like you said with the 21,000 lb max capacity B&W Tow & Stow 3-Ball Mount #BWTS30048B. There is…

view full answer...

Answer 3

Yes, there is a 2-in-1 lock set that lets you lock both the hitch and the ball mount platform of the BulletProof Hitches 2-Ball Mount for 3" Hitch #HD304. What you need is the BulletProof Hitches Receiver Lock for Adjustable Ball Mount…

view full answer...

Answer 4

First you will want to connect an 18 gauge wire to the Temp Sender mounted on your vehicle. You will then route the wire through the firewall into the passenger compartment where the Temperature Gauge is mounted and attach the Temp Sender wire to the…

view full answer...

Answer 5

The only tank equipped RV water heat option we currently offer is the Dometic RV Water Heater part #DMC74FR which is a 120 volt unit with 6 gallon tank and gas/electric operation. In regards to installation, this must be performed by a qualified…

view full answer...

Answer 6

To convert the WFCO WF-8955PEC to be lithium compatible you'd need the part #PD4655V and you'd be set. This fits in the panel without any modifications.

view full answer...

Answer 7

According to Dexter, this is a 3,750 lb torsion axle with a 90.3" hub face measurement. More than likely your axle uses #L68149 and #L44649 bearings with a #168255TB grease seal. You will need to verify this information since Dexter did not have…

view full answer...

Answer 8

Hey Michael, this is a great question but you can use a tongue weight scale like the B and W part #BW34KR with a lighter tongue weight like what you have (relative to it's 4k capacity) and it will still work great. We had the chance to demo this…

view full answer...

Answer 9

Hey Eric! There has definitely been some confusion around the specs on this scale. I just contacted B&W and can confirm that the B&W Digital Tongue Weight Scale w/ LED Screen #BW34KR has a max capacity of 4,000 lbs. It has been listed on our…

view full answer...

Answer 10

Hi Alex; the gauge on the Big Truck Big RV Tongue Weight Scale for Trailers #BTBRV004 has a +/- 5% full scale accuracy and displays weight in 20-lb increments up to 1,000 lbs. We also have it available with a SnapPad #BTBRV99FR. If you want something…

view full answer...

Availability of Dual Ball Mount that Fits 3 inch Hitch on Ford Truck

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching