Replacement 9/16 Inch Wheel Stud for a 7K AxleTek 8-Bolt Hub and Drum Assembly

Question

Question:

I am having difficulty finding replacement studs for my axletek 7000# 8 bolt wheel. The stud is 2.5inch long, 9/16-18 thread, 3/4inch body length, 3/4 inch head diameter, .619 knurl diameter, 1and 9/16inch thread length. The broken stud is the one to replace the other is an incorrect unit supplied by the trailer builder.

asked by: Al S

0

Expert Reply:

The wheel stud you need sounds very close to # K916WB25. I have included a picture showing the dimensions.

Another option that is very close is # 7-257. It has a chart with its dimensions below the features section on its page.

The other 9/16 options we have are either a thread in one, which is not likely what you have, and a shorter model that would not work for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

Hey Scott, I'll need some more more dimensions on the wheel stud to ensure a fit with your trailer hub. Can you measure the spline diameter with a caliper #PTW80157 and the length of the bolt?

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Replacement 9/16 Inch Wheel Stud for a 7K AxleTek 8-Bolt Hub and Drum Assembly

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching