Replacement Master Cylinder Recommendation for Titan Model 6 Drum Actuator T4079200

Question

Question:

Is the T4079200 coupler master cylinder rebuildable?

asked by: Derek

0

Expert Reply:

What would be the easiest solution would be to just replace the master cylinder of the part # T4079200. For that you would want the master cylinder part # T1777401.

expert reply by: Jameson C

0

Answer 1

Hey Andy, The closest direct replacement we have for your Titan is the Dexter #T4750600. This has the same drop head as your titan and uses the same bolt pattern to install. I looked up your Titan 10 and the Dexter is rated for a higher weight…

view full answer...

Answer 2

If you have standard size axles that you are installing the Electric Trailer Brake Kit #AKEBRK-7-SA on then you can choose from the following options: 5,200 lb Axle - Kit #BK3-310 (Grease Seal 2.125" ID) or Kit #BK3-300 (Grease Seal 2.250"…

view full answer...

Answer 3

I would start by checking the condition of the Master Cylinder #T1777401 on your trailer. Using the manual activation method which I have included a image for you to understand this will check to see if the O-rings inside your master cylinder have…

view full answer...

Answer 4

It's a bit hard to tell based on the picture but it does look like you might have an older Titan Model 6 Brake Actuator like our 8K #T4079200. If this is the case then you can use the Replacement Shock #T1242600 to resolve the issues you're…

view full answer...

Answer 5

We've checked the part number you gave us before and the replacement for it is the part #T4750820 which is for disc brakes. This one does come with a reverse lock out solenoid. If it has rust all over it I'd consider just replacing the entire…

view full answer...

Answer 6

That is a great photo, thank you; and while there are certain repair parts available for a Titan Model 6, I recommend replacing it altogether. The reason for this is the corrosion looks to have taken its toll on the actuator, and is at the point…

view full answer...

Answer 7

Hey Larry! If your DA66B is the drum brake model the Demco Hydraulic Brake Actuator #DM72VR is the direct replacement. Since you were asking about the Hydraulic Brake Kit #AKFBBRK-7-D as well I'll assume that is correct. The brake mounting…

view full answer...

Answer 8

On a Titan model 6 actuator like #T4079200 the breakaway reset procedures is as follows: When the break-away lever is engaged, it is in the vertical position. It must be reset before the trailer is moved. First, carefully loosen the pressure line…

view full answer...

Answer 9

Hello Chris, Thanks so much for writing in and a double thank you for including the full brake assembly part number. That is incredibly helpful! Since you have the Kodiak Disc Brake Kit 11.35" Rotor #120 Spindle 12K ALKO #K2HR12A11-120DW, you…

view full answer...

Answer 10

The Demco Hydraulic Brake Actuator #DM8750311 can be used to replace your Tie Down Engineering LP8000 actuator. The Demco comes with an electric lockout like you are wanting. It is zinc coated for corrosion resistance and fits a 2-5/16" hitch…

view full answer...

Answer 11

I wasn't able to reference this part number but we do carry a few wall mount switches for MaxxAir Vent Fans, the part #MA59FR and part #MA00A03550K. If yours look like either of these two options then they will work great for you but they are the…

view full answer...

Answer 12

The Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes #HS481-8067 is designed to be completely plug-and-play so the female end of the 7-way would need to connect to the 7-way cable that's already installed on the trailer…

view full answer...

Replacement Master Cylinder Recommendation for Titan Model 6 Drum Actuator T4079200

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching