Inexpensive Trailer Hub and Spindle for 2,000 lb Axle
Updated 03/05/2020 | Published 09/16/2016
Products Featured in This Question
Question:
i need your least expensive hub and spindle kit
asked by: Bob H
0
Expert Reply:
The most economical priced hub we offer is the part # AKIHUB-440-2-1K. Then for the same in a spindle we have the part # TRU94FR.
This setup is for a 2,000 lb axle with a 4 on 4 inch wheel bolt pattern.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Trailer Hubs and Drums
- Idler Hub
- Pre-Greased
- Standard
- L44643 / L44643
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 8 Inch Wheel
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: led rv lights
- Search Results: trailer lights
- Shop: Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Shop: Trailer Idler Hub Assembly for 2,500-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Shop: Combination LED Trailer Tail Light - Submersible - 7 Function - 14 Diodes - Driver Side
- Search Results: sleeve
- Search Results: accessories and parts
- Search Results: seal sleeve
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Shop: Optronics LED Tail Light - Stop, Turn, Tail - 4" Round - Smoke Lens - Grommet Mount - PL-3
- Shop: RV Designer Rear Trailer Light Kit w/ Tail Lights, Side Marker Lights
- Shop: 20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
- Video: All About the Trailer Idler Hub Assembly for 2,000-lb Axles
- Video: Review of etrailer Trailer Hubs and Drums - Pregreased Idler Hub - AKIHUB-440-2-1K
- Video: A Closer Look at the Trailer Tail Light
- Q&A: Why is There a Driver and Passenger Round Optronics Trailer Tail/Stop/Turn Light
- Q&A: Replacing Hubs and Wheels on 1964 Alpine Sprite Camper Trailer
- Q&A: Replacement 4 Lug Trailer Hub for a 1" Diameter Spindle
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Q&A: Replacement Hub/Drums & Brakes to Replace AL-KO 7230 Hubs
- Q&A: Trailer Hub Recommendation with 4 on 4 inch Bolt Pattern and Bearings L44643
- Q&A: Replacement Galvanized Hub For a Dexter 8-259 with a 1" Straight Spindle
- Article: Most Popular Wheel Bearings
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Trailer Lighting Requirements
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: How to Measure a Trailer Axle
- Article: Trailer Wiring Diagrams
Charlie
3/5/2020
I would like to make a homemade spare tire carrier for the back of my jeep Wrangler TJ 1998 I currently have a heavy steel bumper and I’m considering using a trailer spindle and hub wondering if you have any comments on this project