Would the Guide Ons part # CE27635 Fit a 4 inch Wide I-Beam

Question

Question:

My loadmaster aluminum trailer is 4 inches wide. Will the I beam claps that are provided accommodate this width? Or do I need to purchase additional clamps?

asked by: LAMONT C

0

Expert Reply:

The I-beam clamps of the Guide Ons part # CE27635 that you referenced are confirmed as a fit on I-beams that are between 2-1/2 inches and 4-1/2 inches wide so the kit would fit your 4 inch wide I-beams.

expert reply by: Jameson C

0

Answer 1

Hey Justin, the CE Smith Post Style Guide Ons part #CE27635 that you referenced has corner brackets like you mentioned and not bent tube for the 90 degree turn. The one picture shows an outdated version of the guide ons and I just sent an update to…

view full answer...

Answer 2

I have a solution for you, but the U-bolts included with the CE Smith Post-Style Guide-Ons for Boat Trailers #CE27636 are only good for trailer frames that are up to 5-1/2 inches. You would also need the CE Smith Extra Long U-Bolt Kit part #CE11416…

view full answer...

Answer 3

The metal tubes inside the CE Smith Post-Style Guide-Ons for Boat Trailers - 75" Tall #CE27636 are the uprights. These uprights, which are available at part #CE27605PG, measure 39" tall.

view full answer...

Answer 4

We have the Replacement Upright #CE27605PG which can be used with the 75" CE Smith Post-Style Guide-Ons #CE27636. The replacement upright is a new style and will work in place of the older style which mounted the 2 posts together with a bracket.…

view full answer...

Answer 5

The CE Smith Post-Style Guide-Ons for Boat Trailers - 75" Tall #CE27636 has base bars that are 23 inches long to the outside of the bend. The bars adjusts out to 19" from trailer. I've attached a photo to help.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

Hey Steven! The etrailer Rust-Resistant 3-Leaf Double Eye Spring for 4K Trailer Axles - 25-1/4" Long - Dacromet #e93SR will be adequate for your 2020 Gulf Stream Vista Cruiser since the Dexter D40 number correlates to a 4,000 lbs hub and drum…

view full answer...

Answer 12

Hello Chad, thanks for reaching out. The CE Smith Roller Style Guide-Ons for Pontoon Boat Trailers #CE27672 will work fine with a StarCraft tri-toon, assuming you’ve got a pretty standard bunk-style trailer under it. We’ve put those on plenty of…

view full answer...

Would the Guide Ons part # CE27635 Fit a 4 inch Wide I-Beam

Product Page this Question was Asked From

Continue Researching