Recommendations for Brackets to Mount CE Smith Trailer Fenders # CE19504-2

Question

Question:

Which fender mounting bracket is needed for this fender, CE19504-2? Thanks

asked by: Michael C

0

Expert Reply:

For the set of CE Smith trailer fenders # CE19504-2 you can use existing brackets on the trailer or, if you need brackets, you can use # CE26098G-2. Drilling will be required for installation.

expert reply by: Michael H

0

Answer 1

The CE Smith trailer fender #CE19504 measures 34-1/2 inches from the center of one mounting point to the center of the other. Mounting points are on the underside of the step parts of the fenders. The fender can also be attached via its skirt which…

view full answer...

Answer 2

The CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Black Plastic - 14" Wheels - Qty 2 #CE19504-2 and single fender #CE19504 will attach to your trailer's existing brackets. If your trailer doesn't have the brackets then you…

view full answer...

Answer 3

The CE Smith Single Axle Trailer Fenders w/ Top and Side Steps #CE19504-2 actually does not have any pre-drilled holes for mounting brackets, so you will need to drill the holes yourself to match your existing brackets. The #CE19504-2 measures of…

view full answer...

Answer 4

Hey Michael, thanks for the pictures of the fenders on your boat trailer. The best option is probably the CE Smith Fenders like the part #CE19504 that you referenced. These will require brackets like the part #PF1135-BKT-2 which you could either…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommendations for Brackets to Mount CE Smith Trailer Fenders # CE19504-2

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching