Overall Width of Bulldog A-Frame Trailer Coupler BD43805W0317

Question

Question:

Hi, just wanted to know what the overall width is of this coupler. Thanks

asked by: Mark

0

Expert Reply:

I was able to go out to our warehouse to measure the Bulldog Coupler # BD43805W0317 for you.

I found that the widest part of the coupler is 10-3/4 inches wide. The interior of the widest part is 10-1/4 inches.

I have linked a diagram I made to help you better see the dimensions I took.

I have also linked the Bulldog Coupler to this page for your convenience.

expert reply by: Jackie C

0

click to enlarge

Answer 1

Someone else has recently asked that question and a coworker made a lovely picture showing the measurement you are looking for on coupler #BD43805W0317. I have included that picture for you here. The inner width is 10-1/4 inches and the outer is…

view full answer...

Answer 2

That is correct the inner dimension of the Demco A-Frame Trailer Coupler item #DM14793-95 is 10 3/4 inches. I have attached a picture that breaks down the measurements. You would need to fabricate a spacer on either side to attach this coupler to…

view full answer...

Answer 3

We have the ProGrip Adjustable Wheel Net with Ratchet and Snap Hooks #317-18900 which is designed to fit wheels that are up to 33 inch in diameter and 12-1/2 inches in width. This would work perfectly for you as the ones you referenced are not going…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Overall Width of Bulldog A-Frame Trailer Coupler BD43805W0317

Continue Researching