Replacement Jack Handle and Crank for etrailer trailer jack # TJB-2001S-B

Question

Question:

Can you tell me the part # for the replacement handle/crank on the trailer jack TJB-2001S-B Thanks

asked by: Jeffrey G

0

Expert Reply:

The correct replacement handle and crank for trailer jack # TJB-2001S-B is # TJA-2000S-HD.

I have linked it to this page for your convenience.

expert reply by: Jackie C

0

Answer 1

Hey Charles, the diameter of the handle part #TJA-2000S-HD is 1/2 inch. The handle radius is 6-5/8 inches which is the length number you asked about. The plastic part is 1 inch in diameter.

view full answer...

Answer 2

If the jack you had was the part #MJ-1500B-DWL the correct handle is the part #MJ-1000B-HD. This jack is very common out there so it's most likely what you have but you'd have to look for identifying info on it to determine if it's…

view full answer...

Answer 3

The diameter of the Replacement Sidewind Handle #MJ-1000B-HD that you referenced is 1/2 inch. The radius of the handle is 7 inches.

view full answer...

Answer 4

I measured the Replacement Sidewind Handles #MJ-1000B-HD and #MJ-1500B-HD and found that they both have a diameter of 1/2" and part MJ-1000B-HD measures 2" from the end of the handle to the center of the pin hole while part MJ-1500B-HD…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement Jack Handle and Crank for etrailer trailer jack # TJB-2001S-B

Product Page this Question was Asked From

Continue Researching