Is There a 5 on 4-1/2 inch Bolt Pattern Hub Available for Timbren Axle-Less ASR2KHDS03

Question

Question:

Can the 4inch lift axle less suspension be use with 5-4.5 spindles for a light duty offroad trailer

asked by: Martin

0

Expert Reply:

The Timbren Axle-Less system is compatible with hubs that have 5 on 4-1/2 inch bolt patterns. For just an idler hub you would want the part # 84545UC1-EZ or for a brake hub you would want the part # 84546UC3-EZ.

expert reply by: Jameson C

0

Answer 1

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. Since the figure you came up with doesn't match any of…

view full answer...

Answer 2

To convert your offroad trailer to the Timbren Axle-Less Trailer Suspension System - 4" Lift Spindle w/ Brake Flange - 5,200 lbs #TASR5200S03 you will either use a crossbrace for your trailer frame at the axle location or you will add a 2 inch…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Hi Wesley! We actually have these listed slightly wrong, so I am having that updated. There is a difference and I have that listed below: Timbren Axle-Less Trailer Suspension System - 4" Lift Spindle - **Regular Tires** - 5,200 lbs #T54KV -We…

view full answer...

Is There a 5 on 4-1/2 inch Bolt Pattern Hub Available for Timbren Axle-Less ASR2KHDS03

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching