Will the Pro Series Round Snap-Ring Swivel Jack Bolt on a 2 Inch Trailer Tongue

Question

Question:

I need a trailer jack that will fit the 2 inch tongue on my trailer. Will this one?

asked by: Rob

0

Expert Reply:

The Pro Series Round Snap-Ring Jack, # PS1400300303, will bolt around your 2 inch trailer tongue. This jack can bolt to frames up to 3 inches wide by 4 inches tall and will have no problem fitting on your trailer.

I have attached a photo showing the bolt hole dimensions of this jack for you to check out.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Pro Series Round, Snap-Ring Swivel Jack #PS1400300303 weighs 13 lbs.

view full answer...

Answer 2

The bolt that comes with the Brophy D-Ring Tie-Down Anchor with Backing Plate #DR1S has a diameter of 9/16 inches, so this would be the approximate size of the hole in the backing plate as well. I have added a link to a video review for you to check…

view full answer...

Answer 3

When used along with a steel backing plate, the Brophy D-Ring Tie Down Anchor #LRB1 that you referenced should offer enough support to provide a safe anchor point on the wooden T-Grade OSB flooring on your trailer. With that being said, a better…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Will the Pro Series Round Snap-Ring Swivel Jack Bolt on a 2 Inch Trailer Tongue

Featured Help Information

Miscellaneous Media

Continue Researching