Bull Bar and Front Hitch Recommendation for a 2012 Chevy Silverado 1500

Question

Question:

Is there a combination of a bull bar with light mounts that is compatible with a front mounted hitch?

asked by: Paul J

0

Expert Reply:

Surprisingly the Bull Bar by Westin # 32-2275 would be compatible with the Front Hitch part # 31322 on your 2012 Chevy Silverado.

The hitch installs under the front of the vehicle and attaches to the outside of the frame rails and the Bull Bar installs by inserting into the frame rail and goes through the front fascia of the truck so they would both fit together.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

I am sure we do but Big Tex does not have any kind of database to show what replacement parts fit their trailers. I would be happy to see if we have studs that would work for your hubs, but first I will need to know a few measurements of your current…

view full answer...

Answer 10

Unfortunately we do not have a video of the HappiJac Truck-Mounted Camper Tie-Downs #LC184089 being installed. The Rear anchors are installed in the end of the bumper. There is no precise mounting location since a variety of bumpers may be installed.…

view full answer...

Answer 11

I couldn't be 100% positive about which wheel studs you'd need without seeing the trailer and being able to measure. I just don't have enough information. This bein said, by virtue of the trailer having a 5 on 4-1/2 inch wheel bolt…

view full answer...

Answer 12

For the ST235/80R16 tire, you have a 30.79 inch outer diameter with a 9.25 inch width. Moving up to the ST235/85R16 tire, you will move to a 31.7 inch outer diameter with a 9.3 inch width. As long as you have the space for the extra 1/2 inch in your…

view full answer...

Bull Bar and Front Hitch Recommendation for a 2012 Chevy Silverado 1500

Products Featured in This Question

Continue Researching