Will Optronics Replacement Amber Lens Fit Glo-Brite 118A Amber Trailer Light

Question

Question:

Regarding the answer: I need an Amber Trailer Light To Replace Glo-Brite 118A Trailer Light Question: Do you have a clearance light replacement lens that would work for a Glo-Brite 118A/117R lens Amber thanks. The answer described a similar light, but didnt specify if that lights lens would work on the old 118a light. Will it? Thanks.

asked by: Murray M

0

Expert Reply:

I spoke with my contact at Optronics to see if the lens for their Rectangular LED Trailer Clearance, Side Marker Light with Reflector # MCL44AB will work for the Glo-Brite 118A amber trailer light.

She confirmed that the # A44AB lens will work on the Glo-Brite 118A. The # A44AB lens installs by snapping on to the light housing, and the lens measures 4 inches wide x 1-1/2 inches tall.

expert reply by: Victoria B

0

Answer 1

If you have tapped into the red wire from the 12V battery lead as in the attached diagram, the power is coming from your truck's battery and not the breakaway battery and you'd be just fine. If you are tapped into the wiring in any other…

view full answer...

Answer 2

Yes there will be a fuse that protects the 12 volt trailer accessory circuit of your 7-way wiring. If this is factory wiring of a truck you'll want to check out the fuse box diagram or the owners manual.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The best replacement option we offer for a Atwood GC10A-4E Water Heater is tankless, the Furrion RV Tankless Water Heater part #FR68SR. It won't be a direct replacement but still pretty easy nonetheless as they are very similar. That said, you…

view full answer...

Will Optronics Replacement Amber Lens Fit Glo-Brite 118A Amber Trailer Light

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching