Which Outer Bearing Mates with Inner Bearing LM67048 on a 4-Bolt Hub
Updated 06/29/2010 | Published 06/27/2010
Products Featured in This Question
Question:
I have an older trailer with a tapered shaft. It is a 4-bolt hub. The inner bearing closest to the trailer is an LM67048. The outer bearing appears to have an inside diameter of 11/16 inches. I had a 3/4 id bearing laying around and that is too big so I know for sure it is smaller than a 3/4. I cant make out all of the numbers on the outer bearing, but it looks like an LM11 is the first four digits. The fifth digit appears to be a 7 but its hard to be sure...and the last two digits are not readable. Any idea what bearing I would need for the outer bearing? I did a search on your site using LM11 and the only bearing that came up was an LM11949 which appears to be a 3/4 id bearing and will be too big? Thank you,
asked by: John S
Expert Reply:
We have a 4-bolt hub that uses LM67048 as the inner bearing and an LM11949 bearing as the outer. That is the only hub/bearing configuration we have for an LM67048 inner bearing. It is typically a hub found in agricultural trailer applications. The hub is part # AH15450ECOMP if you want to take a look at it and see if it looks like your hub.
I pulled one of the LM11949 bearings from our warehouse to measure. When measuring bearings, you really need to use a dial caliper. A tape measure is not accurate enough. The LM11949 bearing measures .746 inches or 3/4 of an inch.
What is the bearing number on the 3/4 inch bearing you had lying around that was too big? What is the measurement between two caddy-corner lugs, measured center to center? Using a set of dial calipers, you can compare the measurements of your spindle to spindle part # TRU54FR.
Product Page this Question was Asked From
Replacement Trailer Wheel Bearing - LM11949 - Qty 1
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- .75 Inch I.D.
- Bearing LM11949
- Race LM11910
- 3000 lbs Axle
- etrailer
more information >
Continue Researching
- Shop: Timken Bearing Kit, LM67048/25580 Bearings, LM67010/25520 Races, 412920 Seal
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 6 on 5-1/2 - Pre-Greased
- Shop: Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Video: Timken Bearing Kit Installation - Enclosed Trailer
- Q&A: How to Determine Replacement Trailer Wheel Bearing Sizes
- Shop: Timken Bearing Kit, LM67048 Inner/Outer Bearings, LM67010 Inner/Outer Race, 203013 Seal
- Shop: Seaflo Diaphragm Pump for Boats and RVs - Variable Flow - 3 GPM - 45 psi - 12V DC
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Search Results: trailer tires and wheels
- Video: Timken Bearing Kit Step-By-Step Replacement - Utility Trailer
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Search Results: trailer jack
- Shop: Trailer Wiring
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Search Results: trailer lights
- Shop: Brake Controller
- Search Results: trailer leaf springs
- Search Results: trailer brakes
- Shop: Lift Assist
- Search Results: trailer hubs and drums
- Search Results: spare tire mount
- Q&A: Looking For Brakes And Hubs For 10K American Axles
- Q&A: Availability Of 5 on 4-1/2" Hubs For A 3/4" Spindle
- Q&A: Determining The Correct Replacement Equalizer And Shackle Straps For A 2017 Forest River 5th Wheel
- Q&A: Should Equalizer and Shackles Be Replaced After Being Shoved Out of Position
- Q&A: Determining Correct Replacement Axle For Older Axle With Obsolete L44649 LM11949 Bearing Combination
- Q&A: Best Replacement for Atwood 82543 Brake Actuator
- Article: Trailer Wiring Diagrams
- Article: Most Popular Wheel Bearings