Does the Camco Pop-A-Towel Paper Towel Dispenser Allow Roll to Spin Freely

Question

Question:

Will the paper towel holder on your website keep the roll from spinning loose? And can it be installed vertically? Thanks!

asked by: Brenda R

0

Expert Reply:

The paper towel holder part # CAM57111 that you referenced will end up touching the ends of the paper towel roll when one is installed so there would be enough friction in the setup to prevent the roll from being able to just spin freely. You will still will be able to unroll the roll when needed for grabbing a paper towel.

There is no reason you couldn't install this vertically either.

expert reply by: Jameson C

0

Answer 1

Hey Thad, the Flint Hill Goods Adj Ball Mount #FHG25VR measures 3 1/8" from the center of the hitch pin hole to the edge of the gusset, so it should clear the vehicle easily. What sort of stuff are you hauling with your Toyota? Let me know in…

view full answer...

Answer 2

That is an interesting question. I can honestly say that we have not heard of this rule before. It does make sense though, that a ball mount with a 10" or larger drop could not hold as much weight as one with less drop. We ran this question by…

view full answer...

Answer 3

The Convert-A-Ball Ball Mount for 2" hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs item #AMSC10 that was previously referenced is a superior hitch to the Brophy 10" drop item #BM10. It is a stronger reinforced hitch that has a…

view full answer...

Answer 4

I recommend looking at the Stainless Steel Locking, Anti-Rattle Threaded Hitch Pin for 2" Trailer Hitches #SR25219, which is going to give you the security you need and does a great job at eliminating rattle on hitch mounted accessories. There…

view full answer...

Answer 5

The Camco Paper Towel Holder part #CAM57111 will stick out about 7-1/2" once installed. The overall length of the holder is 12-1/4". I have attached a diagram for your reference.

view full answer...

Answer 6

The lock that goes with the Softride threaded bolt #SR25879 is now longer available for sale as a separate part. They are using a different design now and have discontinued that particular lock. But you can get a replacement by getting a whole…

view full answer...

Answer 7

The SoftRide #SR25219 locking and anti-rattle hitch pin is not available keyed alike. The next best thing is the etrailer #e98882 stainless steel locking hitch receiver lock which can be keyed alike on the order page in any quantity you need. To…

view full answer...

Answer 8

On Curt ball mount #C45338 it measures approximately 5 inches from the center of the pin hole to the support gusset. However, the welds could be slightly different from one to the next so on some it will be less and others it will be more but only by…

view full answer...

Answer 9

Based on what you mentioned it does seem like a rise of about 7 inches or so would be ideal for you. For a fixed ball mount the part #C45338 would be a really great option or for a more universal solution an adjustable ball mount like the part…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Does the Camco Pop-A-Towel Paper Towel Dispenser Allow Roll to Spin Freely

Continue Researching