2013 Chevy Silverado Camper Shell Wiring Recommendation

Question

Question:

Im trying to wire the third brake light for the camper shell on my 2013 Silverado. Any ideas?

asked by: Clint

0

Expert Reply:

The main trailer wiring harness is located under the truck bed, usually above the spare tire. There is usually a socket for your trailer connector to plug into, but if you peel back the wire loom you will find a light blue wire further up in the wiring harness that is intended for use for a third brake lamp on a camper shell.

I attached a couple pics to help you see where the wire is at.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Your 2024 Chevrolet Silverado 3500 will come with a 2-1/2" trailer hitch receiver. If your truck did not come with a reducer for a 2" receiver we do have the B&W #BWRHXA2182 if you need to use your 2" ball mount or hitch mounted…

view full answer...

Answer 2

Once you have located the Center High Mount Stop Light wire (labeled as CHMSL) under your driver's side dash of your 2013 Chevrolet Silverado (bundled with your brake controller wiring) you will need to run wire from the cab of your Silverado to…

view full answer...

Answer 3

Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers part #PAL9772 or part #PAL9555 will work on the Leer 100XQ Truck Caps because it uses a cable latching mechanism and the handle is not riveted on.

view full answer...

Answer 4

Yes. Thule Square Bars like the #TH712400 are compatible with the Thule Rapid Podium Feet #TH460R. In order to mount the #TH460R to your 2014 Subaru Impreza you'll also need the Fit Kit for Thule Podium-Style Roof Rack Feet- 3068 #THKIT3068.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

2013 Chevy Silverado Camper Shell Wiring Recommendation

Product Page this Question was Asked From

Continue Researching