Can a Single Weight Distribution System Be Used for Multiple Trailers with Various Weights

Question

Question:

Looking at getting a weight distribution hitch. I tow alot of trailers all different sizes and loads. Can I just get one setup that would be a best all around fit? I dont want multiple trunnon bars.

asked by: Anthony

0

Expert Reply:

Weight distribution systems are rated for different tongue weights and gross trailer weights. They are designed to work best with trailers that fall within their rating. The tongue weight rating is the most important factor in determining which size weight distribution system you should use.

If the bars of the system are rated too high for your setup, they will create a rigid ride, which can result in a bouncing trailer. If the bars are not rated high enough, the system will be unable to properly distribute the weight, rendering it virtually useless.

For example, the Reese Steadi-Flex Weight Distribution System # RP66559 is rated for trailers with tongue weights between 500-1,000 pounds, with a maximum gross trailer weight of 10,000 pounds. This system would be ineffective on trailers with tongue weights higher than 1,000 pounds, and would cause a very stiff ride with trailers that have tongue weights lower than 500 pounds.

expert reply by: Victoria B

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi Jeff, The K-Source Snap & Zap Custom Towing Mirrors part #KS69NQ will work with your Lariat mirrors while allowing you to retain the use of the camera and side lights! These mirrors are specifically designed to match the contours of the side…

view full answer...

Answer 12

Hi Bill! Thanks for your pictures, they were extremely helpful! ^___^ The LCI Part #194170 on that tag you found means you have a 1621 pin box. The Gen-Y #GY45SR you were looking at is specifically for the Lippert 1116 and 1716 pin boxes, so you will…

view full answer...

Can a Single Weight Distribution System Be Used for Multiple Trailers with Various Weights

Featured Help Information

Miscellaneous Media

Continue Researching