18 Inch Long Flexible Brake Hose for Trailer with Hydraulic Drum Brakes

Question

Question:

I need a brake hose from the T to the passenger side brake on my 2001 EZ Loader. Model 1-TSTCL96B 2-22 4000 H1X 3500, Ser # 1ZERAUNG41A131796. The hose appears to be 16inch to 18inch long. A 3/8inch wrench fits the T end and a 1/2inch wrench fits the brake end. I have drum brakes. Can you give me a part number?

asked by: John M

0

Expert Reply:

Flexible brake line # T0776500 is a good option. It is 18-25/32 inches long and uses 3/8"-24 UNF male and female fittings on each end.

expert reply by: Michael H

0

Answer 1

The closest option we have to replace your Atwood 82543 actuator is part #DM72VR. However, it doesn't have the lockout like your Atwood does. To add a lockout use #T4748800 but it's an electric lockout unlike the Atwood's manual lockout.…

view full answer...

Answer 2

For a replacement brake line I recommend the Titan Hydraulic Brake Line with Fittings #T0776500. This brake line is 18-25/32" long, has a male and female end, and has 3/8"-24 UNF fittings. The thread size on 3/16" fittings is…

view full answer...

Answer 3

I took a look at your Titan Zinc-Plated Brake Actuator #T43397007K, and I do not think that's a quick disconnect line, I actually believe what you're needing is: - The Titan Hydraulic Brake Line with Fittings #T0776500. This line measures…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

18 Inch Long Flexible Brake Hose for Trailer with Hydraulic Drum Brakes

Product Page this Question was Asked From

Continue Researching