Replacement 18 Inch Long Brake Line with Male and Female 3/16 Inch Fittings

Question

Question:

I am looking for a brake hose 18inch long with 3/16inch fittings, one male one female end. Can you help! Thank You

asked by: Bob

0

Expert Reply:

For a replacement brake line I recommend the Titan Hydraulic Brake Line with Fittings # T0776500. This brake line is 18-25/32" long, has a male and female end, and has 3/8"-24 UNF fittings. The thread size on 3/16" fittings is 3/8"-24 so this will be the same as the hose you have now.

I have attached a review video for your reference.

expert reply by: Robin H

0

Customer brake line.
(click to enlarge)

Answer 1

Yes you will need a new electric over hydraulic actuator to go from drum to disc as the disc brake setups require a higher psi rating. The best option is the HydraStar part #HBA16 as it has the best reputation for reliability and is the fastest…

view full answer...

Answer 2

It looks like that is a piece of flexible brake line you are using. You would need standard flexible brake line with a 3/8 inch male fitting. We offer them in varying lengths. A 13 inch long brake line with fittings (male on one end, female on the…

view full answer...

Answer 3

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

Answer 4

You should be able to get the nylon bushings out fairly easily. In the worst case scenario, you can use an old 5/8 inch bolt or piece of round bar stock and punch the bushing out. The bronze bushings can be pounded in with a mallet or a hammer. If…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You don't have to worry about drilling into your trailer's suspension. We have bushings that will fit the 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/8" Long item #e68SR you found that will fit your trailer. You will want…

view full answer...

Answer 7

I am not sure which exact dimension you are looking for but the good news is that if you have properly installed brake mounting flanges there would be no need to verify clearance between the brake assemblies and the drums as all of that would be…

view full answer...

Answer 8

Yes, there is a way to back up your boat trailer and keep the surge brake actuator, #T43397007K, from applying pressure to the trailer brakes. You will need an electric lockout solenoid, #T4748800, which will close when you shift the vehicle into…

view full answer...

Answer 9

The backup light circuit of a vehicle would provide enough amperage to activate the lockout solenoid on a trailer with surge brakes. I'd make sure that the extra blue wire of your #47515 does have voltage when the reverse lights are on to verify…

view full answer...

Answer 10

How long of a line do you need? Do you know what size you need? The most common size is 3/16 inch like part #BH-3MFS-4-5 which is 54 inches long.

view full answer...

Answer 11

The thread size is 3/8"-24 but the fitting size is 3/16". This standard for trailer brake lines. This will go from 1/2 inch thread size to 3/8 inch. If the dimensions you took are 1/2 inch and 3/8 inch of the threads this will fit.

view full answer...

Answer 12

Finding information on the Tie Down 46250 was not an easy task as it was discontinued awhile back. From what I could find, it looks like the calipers marked 46250 often times have to change the mounting bracket and rotor/hub in addition to the…

view full answer...

Replacement 18 Inch Long Brake Line with Male and Female 3/16 Inch Fittings

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching