Replacement Motor For Venture Landing Gear on a 5th Wheel Trailer

Question

Question:

Does LC142178 replace venture motor model # 1A065012-02-01 made in 2009?

asked by: Pat S

0

Expert Reply:

Replacement motor # LC142178 is the only motor Lippert still makes for the Venture landing gear. Since your landing gear was made in 2009 there should be no problem with this motor fitting your landing gear.

expert reply by: Michael H

0

Answer 1

The replacement landing gear motor you referenced, Stromberg Carlson #LG-142178, is a widely compatible replacement motor that will work with most major brands of 5th wheel landing gear, including Stromberg Carlson, Lippert, Venture and Atwood. These…

view full answer...

Answer 2

The composite gearbox, part #75054SP is designed for use with standard, heavy, and super duty landing gears. The replacement gearbox, part #LG-179015 has been used by several customers and they say it is a great fit. This gearbox is made of aluminum…

view full answer...

Answer 3

Your ST235/85R16 tire is 31.7 inches diameter, so I recommend the Adco Ultra Tyre Gard RV Wheel Covers - Single Axle - 30" to 32" #290-3952 for a cover with a connector to hold it in place. If you want a cleaner and easier install the…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Motor For Venture Landing Gear on a 5th Wheel Trailer

Continue Researching