Distance From Pin Hole to End of Shank on the Curt Ball Mount C45090

Question

Question:

On Curt ball mount # C45090 can you please tell me the measurement from the center of the hitch pin hole to the open end of the shank? Thank you.

asked by: John T

1

Helpful Expert Reply:

It sounds like you are asking about the distance from the center of the hitch pin hole to the back of the shank of the ball mount that slides into the hitch. That distance is 2-1/2 inches.

I attached a picture that shows this dimension as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The Curt #13077 and Draw-Tite #75600 are both at a weight rating where it could be considered a class III or IV. A class III is rated up to 6,000lbs with up to 600lbs of tongue weight. While a class IV is rated higher there is not a specific number…

view full answer...

Answer 2

It sure will Danny and thanks for all the detailed information! The 50 Amp Furrion Automatic Transfer Switch item #F50ATS is exactly what you need. It is compatible with your WFCO AC Distribution Panel and is going to work great with your Onan…

view full answer...

Answer 3

Yes, the Furrion Automatic Transfer Switch - 50 Amp - 125/250V #F50ATS is a compatible replacement for your Intellitec 50 amp transfer switch. This transfer switch automatically reroutes your RV's AC input from shore power to generator power when…

view full answer...

Answer 4

The Furrion AC/DC Distribution Panel will work to replace the WFCO WF-8930/50 distribution panel but is not considered an exact replacement. We do not carry a distribution panel that is an exact replacement for that WFCO model but the Furrion will…

view full answer...

Answer 5

Yes. You could use the Progressive Dynamics #PD52 to replace your Furrion #F50ATS; they're both rated for 50amps so they are compatible. The Furrion does provide a bit of extra protection against power surges though with it's 125/250v supply,…

view full answer...

Answer 6

Since the Furrion Automatic Transfer Switch #F50ATS is only rated for 3,750 watts I recommend going with the Go Power Automatic Transfer Switch #34270278 instead. I reached out and confirmed with my contact at Go Power that this transfer switch will…

view full answer...

Answer 7

It is possible to use a 50 Amp transfer switch with a 30 amp setup since you plan on upgrading in the future however, the Furrion Transfer 50 Amp Switch is made for 50 Amp setups. I recommend to use Progressive Dynamics 50 Amp Transfer Switch part…

view full answer...

Answer 8

The transfer switches that we currently offer are either rated for 30 amp or 50 amp service and can't function properly if wired to a different amperage rating. For example, if your motorhome had 50 amp service and you installed the Furrion…

view full answer...

Answer 9

On the top panel of the Furrion Transfer Switch #F50ATS is a diagram that shows how it will wire to your Weekend Warrior. I also attached a second picture that shows what's underneath the lid.

view full answer...

Answer 10

Hello Greg, Great question, and yes level towing is important. The average height for a mid-size to full-size travel trailer is 22 to 28 inches, the average height for an F-350 with 4 wheel drive is 20–24 inches, with that being said you will most…

view full answer...

Answer 11

I have a power cord which is the same thing but more so what you're looking for. This cord is rated for 125 and 250V unlike the one you were looking at. The SmartPlug RV Power Cord - 125/250V - 50 Amp - 30' Item #SM86FR is rated for 125/250V.…

view full answer...

Answer 12

I recommend the Roadmaster Dual Hitch Receiver Adapter, 10" Drop/Rise item #RM-077-10. This adapter was designed for this type of set up. Your Jeep Rubicon and Swagman E bike rack weigh well below the 10,000 lbs maximum capacity of this hitch. I…

view full answer...

Distance From Pin Hole to End of Shank on the Curt Ball Mount C45090

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching