Dimensions Of Air Compressor Housing For Roadmaster BrakeMaster Brake System # RM-9060-900002

Question

Question:

Can you please tell me the dimension of the air tank/compressor assembly L x W x H ?

asked by: Mike S

0

Expert Reply:

I pulled one of the Roadmaster BrakeMaster systems, part # RM-9060-900002 from our warehouse and took some measurements you requested.

The air compressor housing measures 10 inches wide at the front, 8 inches deep, 10-3/4 inches tall and the width including the mounting flanges on the back of the housing is 12 inches. This system is designed to work with RVs that have hydraulic brakes. It includes all of the hardware and installation instructions.

expert reply by: Jeffrey L

0

Answer 1

There are two methods of installation for the Roadmaster Brake Lite Relay part #RM-88400 that you referenced, open and closed. Most towed cars require the normally open installation method. Ford and Lincoln models with neutral tow kits and most…

view full answer...

Answer 2

If your motorhome brake line has metric fittings, it will be necessary to use a metric-to-standard T-fitting to attach the proportioning valve. This fitting is not supplied in the RoadMaster BrakeMaster Second RV Kit for Hydraulic Brakes #RM-98300.…

view full answer...

Answer 3

What you described is actually the part #RM-8315 that is a component of the #RM-9060 and #RM-9060-900002. It is the air tank/air compressor assembly.

view full answer...

Answer 4

If by pressure switch you mean just the break away switch for your Roadmaster BakeMaster 9000 then you can use part #RM-650898. For a complete BrakeAway Kit including the switch and air cylinder use part #RM-8600. If you refer to the Pressure Reducer…

view full answer...

Answer 5

The Replacement Air Compressor #RM-8315 is the correct part for the Roadmaster BrakeMaster #RM-9060.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Thanks for the information Kevin! To flat tow your 2025 Ford Bronco with a standard bumper and LED lights, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item #e84ZR Base…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Dimensions Of Air Compressor Housing For Roadmaster BrakeMaster Brake System # RM-9060-900002

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching