Brake Magnets Needed for 2010 Surtrac Trailer with 5200 LB Axles

Question

Question:

i need to replace my brake magnets and i have 5200 axles. i dont know if it is a 6k or 7k magnet. it is a 2010 surtrac trailer so reltivally newer axles. just wondering if there is a differance or if it does not matter. thank you

asked by: Eddy

0

Expert Reply:

I spoke with my contact at Dexter Axle and if there is any question regarding capacity, he recommends going with a magnet for a 7K axle brake assembly. The magnet is interchangeable so if you do indeed have brake assemblies for a 6K axle, it will still work for you. The magnet will be just a bit stronger but will not cause you any issues.

Currently we offer 2 options when it comes to brake magnets for 12 inch x 2 inch brake assemblies.

Trailer Brake Magnet, # BP01-180, fits:
Dexter 12" x 2" 6K
Alko 12" x 2" 6K and 7K after 1988(not centerline)
Hayes 12" x 2" 6K and 7K after 1988(not centerline)

And

Trailer Brake Magnet, # BP01-225, fits:
Dexter 12" x 2" 7K

expert reply by: Leah S

0

Answer 1

Electric drum brake assemblies for 6k and 7k axles both use the same 5 bolt mounting pattern. The 7k brakes will have a stronger magnet and will provide more braking. If used on a 6k axle a 7k brake assembly can be too aggressive but it could be…

view full answer...

Answer 2

As you may have already found, 5200 lb, 6000 lb and 7000 lb axles can all use the same components including inner/outer bearings, hubs and brakes. Here are some other things they share in common: Dexter 5200 lb Regular Duty Axle - 0.180 inch tube…

view full answer...

Answer 3

When a brake controller like your Draw-Tite Activator #5100 does not light up to indicate that is senses a connected trailer, then often the problem is in either the vehicle-side or trailer-side connectors. Since the manual override does not activate…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Brake Magnets Needed for 2010 Surtrac Trailer with 5200 LB Axles

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching