What is the Mounting Hold Spacing for Dutton Lainson 1500 Pound Swivel Trailer Jack

Question

Question:

I have a trailer in need of a tongue jack replacement. The existing jack is bolted to the trailer because of space constraints. Can you tell me what the hole spacing is on the DL22800 and the hole sizes? Thanks

asked by: Mark

0

Expert Reply:

I went out to the warehouse and pulled Dutton Lainson trailer jack # DL22800 to take the measurements for you. The 3 holes closest together are 1 inch apart on center. From the third hole to the furthest away hole is 2-1/2 inches. Side to side the holes are 5-1/2 inches apart on center. The hole diameters are all 0.39 inches for use with 3/8 inch hardware.

expert reply by: Michael H

0

Answer 1

The wheel of the etrailer.com jack part #MJ-1500B is the part #JWK-8P which has a center hole diameter of 5/8 inches. There's a bushing that fits into the wheel where a 1/2 inch bolt fits into as well.

view full answer...

Answer 2

Hey Tammis, yes the Dutton Lainson Swivel Jack part #DL22800 that you referenced will work on a trailer frame that is 3 inch by 3 inch.

view full answer...

Answer 3

I can certainly provide those measurements for you! I spoke with my contact at Dutton-Lainson about the Pull Pin, Easy Swivel Trailer Jack #DL22800 and Replacement Wheel #DL22410. He confirmed that the inner bore of the wheel measures 0.645 inches.…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

What is the Mounting Hold Spacing for Dutton Lainson 1500 Pound Swivel Trailer Jack

Product Page this Question was Asked From

Continue Researching