Replacement Swivel Handle Kit Part DL22449 Measurements
Published 03/05/2015
Question:
I have an old trailer do not have the mfg of it and need a new Swivel Handle Kit. It measures 3/8inch in diameter, the straight part with the cotter pin hole measures close to 3 inches long. From the center of the cotter pin hole to the open end of the straight meausres 1 7/8 Do you have anything that would would work? It appears part DL22449 is very close but it does not give me the full specs to compare. Thank you for your time
asked by: Sean D
Expert Reply:
I went to our warehouse to get the swivel handle kit # DL22449 to provide you a few measurements to determine if this is the right part for your swivel jack.
From the center of the cotter pin hole to the end of the handle is 1-1/2 inches. This measurement may be a tad to small from what you referenced of 1-7/8. The diameter of the swivel handle is 3/8 of an inch. The length of the handle from the end (end closest to the pin hole) up to the nearly 90 degree angle is slightly over 2-1/2 inches. I included a diagram and short video showing you the measurements.
This kit consists of a replacement 3/8-inch diameter pull pin, spring, washer and cotter pin. Instructions are included.
Another possibility could be # BD500103. It has a diameter of 3/8 inches. The hole center to end of the pin is 7/8 inches.
We just don't currently have a replacement swivel handle with the measurement of 1-7/8 inches.
Product Page this Question was Asked From
Replacement Swivel Handle Kit for Dutton-Lainson Jack
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Pins and Clips
- 3/8 Inch Plunger Pin
- Dutton-Lainson
more information >
Continue Researching
- Shop: Replacement Swivel Handle Kit for Dutton-Lainson Jack
- Shop: Replacement Swivel Pin Kit for Trailer Jacks
- Shop: Replacement Plunger Pin Assembly for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Search Results: plunger pin
- Q&A: Replacement Swivel Handel Pin For a Dutton Lainson Jack On Shoreland'r Boat Trailer
- Q&A: Comparing the Dutton-Lainson Swivel Pin to the Fulton Swivel Pin
- Q&A: What is the Diameter of Replacement Pull Pin # DL22454
- Q&A: Spring Loaded Jack Pins For Harbor Freight Jack
- Q&A: Replacement 3/8 Diameter Plunger Pin Assembly
- Q&A: Replacement Snap Ring and Plunger Pin for Fulton FTJ120W0301
- Video: Review of the Replacement Swivel Handle Kit for Dutton-Lainson Jack
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Q&A: Replacement 3/8 Plunger Pin Kit for Fulton Marine Jacks
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: How to Choose a Trailer Brake Controller
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer jack
- Shop: Brake Controller
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Search Results: trailer lights
- Video: Measuring To Choose The Right Trailer Axle
- Article: How to Measure Your Trailer Wheel Bolt Pattern
on Accessories and Parts
