What Size is the Mounting Bolt for Rectangular Tractor and Utility Light # TL46TS

Question

Question:

What size is the outside diameter of the mounting stud?

asked by: Waylon

0

Expert Reply:

I went out to the warehouse and pulled Rectangular Tractor and Utility Light # TL46TS to measure the mounting bolt. Using a bolt measuring tool I found that it uses a 1/2 inch coarse threaded bolt.

expert reply by: Michael H

0

Answer 1

The SAE number isn't typically a great way to track down replacement lights as it's not a part number so I don't know exactly what light you are looking for but the Optronics light part #BU70CB that you referenced is a clear light that is…

view full answer...

Answer 2

The Opti-Brite LED Work Light #TLL60FB is a 2-wire light with black being power and white being ground. It will wire in to your trailer's existing wiring. As long as the current lights run on 12, 24, or 36 volt DC this light is compatible.

view full answer...

Answer 3

I would be happy to provide you with the dimensions of the #TL35FS Optronics Utility Work Light - Incandescent - Flood Beam - Rectangle - Clear Lens. The measurements you are looking for are 6-5/8" long x 4-5/16" wide x 3-13/16" deep.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Size is the Mounting Bolt for Rectangular Tractor and Utility Light # TL46TS

Featured Help Information

Miscellaneous Media

Continue Researching