Spare Tire Carrier Recommendation for a Diamond Cargo Trailer with a 2x6 Frame

Question

Question:

I need a spare tire holder for the tongue of my new Diamond Cargo enclosed trailer for a 15 in tire. BUT the frame is 2 in wide by 6 SIX inch tall - do you have ANY models that will bolt to a trailer frame that is 2X6 inches?? Thanks!

asked by: Drew B

0

Expert Reply:

The only spare tire carrier I can recommend for your trailer frame would be a U-bolt carrier like the part # CE22011Z-11050-2. This is compatible with rims up to 15 inches in diameter and can be used with 4 and 5 bolt patterns. The rim will have to be installed on the frame like the picture I attached shows.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We actually have a spare wheel carrier for trailers with angle-iron rails with the etrailer Spare Tire Carrier for Trailer with Angle-Iron Railing #e99045.

view full answer...

Answer 2

We do have wheel chocks which should work very well for you. The FloTool Wheel Chocks for Up to 20" Wheels #FT11930MI are 8-1/8" long x 6" wide x 4-5/8" tall and, as the name says, will work for wheels that are 20" or…

view full answer...

Answer 3

Since you have wooden floors in your trailer the hardware I would recommend for installing e-track like the part #EM19147 would be the Erickson Hardware kit part #SL49FR which is basically wood screws.

view full answer...

Answer 4

In order to secure your 2018 Harley Davidson Tri Glide I recommend using the Tow-Rax Wheel Chock part #TWSPWM for the front wheel so long as it is not greater than 6-1/2" wide. Then in order to secure the two rear wheels I recommend using an…

view full answer...

Answer 5

Aluminum is a pretty soft metal. Especially as thin as you mentioned. I wouldn't recommend self tappers for the e-track. Instead I would recommend appropriately sized nuts and bolts on either side of the track with larger washers.

view full answer...

Answer 6

There will still be metal studs behind the fiber glass wall in the box truck, so you want to purchase a stud finder that is capable of detecting metal studs to attach your track to. I am not entirely sure what you are trying to build when you mention…

view full answer...

Answer 7

In order to install horizontal E-Tracks, like the etrailer #e42VR, you're going to have to install supports inside your trailer to fix them to. According to my research that CellTech wall isn't solid enough to drill into which is why supports…

view full answer...

Answer 8

The zinc plating on the Erickson E-Track #E19148 will actually prevent the underlying steel from coming into contact with the aluminum, so the risk of corrosion of the aluminum is reduced significantly. That being said, you will want to use something…

view full answer...

Answer 9

On an 4 foot long section of E-track #EM19147 and 2 screws every 16 inches that is a total of 6 screws in the aluminum frame. This most likely will not get you near the capacity of the E-track. I recommend bolting through the aluminum frame so that…

view full answer...

Answer 10

The minimum height for the Trailer Valet XL #TVXL2 is 19-1/4 inches. The maximum height is 20-1/4 inches. Please keep in mind that when leaving the Trailer Valet hooked up to your trailer on a slope that you will want to use chocks, like part #3605,…

view full answer...

Answer 11

That is going to come down the thickness/type of metal underneath the 3/4" plywood floor on your trailer. If the metal is the frame or crossmember and is made of steel then the Snap-Loc E-Track Self-Drilling Metal Screws - Qty 20 #SL99FR would…

view full answer...

Answer 12

Self tappers like the part #SL99FR would work great as they have drill bits on the end which would make it through the metal of your studs and then attach.

view full answer...

Spare Tire Carrier Recommendation for a Diamond Cargo Trailer with a 2x6 Frame

Product Page this Question was Asked From

Continue Researching