Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
5-1/2" Round. LED trailer light with 7 diodes provides backup light function. LumenX optics creates a solid panel of light. Integrated voltage regulation. Mounts on surface of trailer wiith built-in flange. Accepts AMP plug.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Ellen: Hey, everyone. I'm Ellen here at etrailer.com. And today we're going to take a look at the Lumenex LED trailer backup light. This helps you to see where you're going in the dark whenever you're backing up with your trailer. So you're going to extend that light out to the back of your trailer rather than just having the backup lights from your towing vehicle. So you get a little bit more illumination there.
Helps you see where you're going. The thing that I really like about this light is that it is LED. It's going to be a nice bright, nice looking light. So the advantage with LED is that there's really no maintenance required with incandescent bulbs. You typically have to replace those bulbs out at some point, because they go bad.
This we don't really have to worry about that. It should be a long lasting light and have less power draw as well as compared to our incandescent light.So can you have more of these without running down your battery as quickly, or taking as much from your towing vehicle depending on your setup. But as far as how to wire this up, you will need a plug. It does not come with it. So you will have to pick one up from us here at etrailer.com.
This one isn't quite the right one, but it's the one I have here in the studio. So you really just need a two wire plug. There's just two wires to connect with this, since all it does is turn on and off. But it should plug in just like that. And then voila, nice bright light.
So it's pretty easy to install it. You will need a four and a half inch hole for that to fit into. Again, nice bright light there. And turn the light out in the studios so you can get a better idea of what that looks like in the dark.So especially if you have two of these, it should be enough to illuminate that area behind you. Just pulling it away from the table so you can see what it looks like further out. I like this kind of concentric circle design. It looks pretty cool. Almost like a snowflake, or kind of ripples in a pond. So it just looks cool. I like it.As far as other measurements with this . Unplug it from our wiring and we can go over those. The outer diameter going from the outer edge of this flange is five and a half inches. You can see that there from edge to edge, five and a half. The light itself is about four and a quarter inch in diameter. And then again the opening or the cutout that you'll need is four and a half inches. The thickness going from the surface of the light to the back of where that wiring will plug in is about three . Or excuse me, one and three eights. There's a total of seven diodes. The power draw at 12 volts is going to be 0.23 amps. So a pretty low power draw as I mentioned before. This is made in the USA, DOT compliant. That plug at the back is an AMP style plug for your weather tight connection.Again, you can find those here at etrailer.com. It's compatible with 12 volt DC systems. The lens is a clear lens, polycarbonate. So it should be pretty durable. Same for the housing. And that design also ensures that it has a consistent light output, and also prevents it from any kind of overheating. So it should be a nice little light for a long time. You really shouldn't have to worry about replacing this unless something happens to the housing overall, it gets cracked or bumped, or something like that. Cracked or damaged, or something like that. It does have a limited lifetime warranty. And that pretty much does it for our look at the Lumenex LED trailer backup light. I hope this video has been helpful in deciding if this is going to be the right light for you. If not, we do have a lot of other options available here at etrailer.com. So please check them out. Thanks for watching.
Average Customer Rating: 4.6 out of 5 stars (108 Customer Reviews)
5-1/2" Round. LED trailer light with 7 diodes provides backup light function. LumenX optics creates a solid panel of light. Integrated voltage regulation. Mounts on surface of trailer wiith built-in flange. Accepts AMP plug.Great product. Did not listen to my salesperson Jesse. I do need the 2 prong adapters.
Very nice looking lights. Disappointed in that I did not watch the video to see that a harness is needed to wire the lights. I will get them with next order though.
Easy installation. Working perfectly after 1year
This is a review of etrailer as the product is 4*. The lights came loose in a box so all 4 lights lenses are scratched. When you spend 16-21$ a light you expect them to handle with care but they don’t.
This is a review of etrailer as the product is 4*. The lights came loose in a box so all 4 lights lenses are scratched. When you spend 16-21$ a light you expect them to handle with care but they don’t.
Purchased these in April, installed in May. Second trip I made with the trailer in July, the lens fell off one light. No damage, it just fell off.
Neither E-trailer, nor Peterson will warranty the light.
I think it's the last time I spend money with either of them.
Exactly what you'd expect. Seems to be a good quality grommet-mount LED light. I used it for a mid-ship marker on a gooseneck.
Two of the three lights I installed randomly turn themselves off. At times they also require multiple “touches” to operate, which can get frustrating.
The light is very bright and is good quality I love it
Good product, nice bright led's
Should last a long time. Great customer service and good website description of product. Etrailer has always been a great company to deal with. Keep up the good work.
perfect timing on the ETA of parts Thanks alot
Bought 4 tail lights only 1 worked right out of the box - had to work with the other 3 to get them to work
Exactly what we were looking for. I do think the description needs to be more clear as I ordered an extra wire that actual came with the light. Other than that received the product earlier than expected and we were able to finish the job for the customer sooner.
I was worried that the backup lights would not be bright enough, but they’re surprisingly bright for only one segment of the light.
Easy instillation and very bright. But you must be very thorough that you have the right sized grommet for the hole in the bed or trailer AND for the light you are using. Not all grommets are the same as with trailers and flat beds so make sure that you double check the hole size both ways of the bed and the light to minimize head aches when you go to install.
I used these to replace the tail lights on my utility trailer. They are bright and because they are LED they will not require any attention. I look forward to many years of reliable service.
Thank you for the prompt service.
These worked great
Great light but would need to manually turn them on each time you kill the main switch in the horse trailer. Will reorder the same light but without the touch switch in the middle of the lens. Bad on me for being a poor electrician.
Perfect replacement for my damaged tail light on our new Timpte 720 aluminum car hauler. Shipping was very quick and packaging was perfect. Thank you for the great service.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Katrina B.
5/11/2023
Well lets get you back over to Jesse for them to help you get the parts they suggested.