To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Features:
Get the advantages of both a hard tonneau cover and a soft tonneau cover for your vehicle with the Revolver X2. This hybrid tonneau likely has an identity crisis. It's built like a hard cover, but it looks and acts like a soft cover. With the Revolver X2, you get the strength, durability, and security of a hard tonneau and the sleek look and convenience of a soft, roll-up tonneau - all while protecting your truck bed and cargo and helping to improve your fuel mileage.
The secret to the Revolver X2's versatility is the aluminum slats on the underside of the cover that make it strong, seamless, and flexible. These individual, hinged slats give the cover its rugged body, while also allowing enough flexibility for the cover to be rolled up. Atop the slats is a tough, 1-piece vinyl layer that adds to the tonneau's sleek look and overall durability while also keeping the slats perfectly aligned. As a result, the Revolver X2 will roll up evenly every time, unlike ordinary soft vinyl covers that can get lopsided as you maneuver them.
Unlike other tonneau covers that sit 1/2" or more above your truck bed rails, the Revolver X2 sits nearly flush with your rails for a clean, ultra-sleek look.
The Revolver X2 gives you full use of your truck bed in a matter of seconds - just roll up the cover and secure it behind the cab. As a result, you can tote around all your gear without having to remove the tonneau. And because the Revolver X2 mounts inside your truck bed rails, you can still use your truck bed stake pockets to mount accessories like tie-down anchors.
The Revolver X2 is simple to operate. Following installation, just roll the cover out and press down on the rearmost slat at the tailgate to secure the tonneau in place.
The built-in latches not only lock down the back end of the tonneau, but they also fasten the sides of the Revolver X2 along the length of the frame rails. The rail tooth runs the entire length of each frame rail. It rotates downward to lock the side rail into the sides of the cover.
When the cover is rolled out and the rear slat is pressed down at the tailgate, the latches on both sides engage. When this happens, the integrated teeth pivot down and rest on top of each slat of the rolled-out cover. Closing the rear slat effectively pins the cover to the rails, ensuring that the cover stays closed from front to back. It's that simple - no Velcro to seal or snaps to wrestle with. When your tailgate is closed and locked, no one will be able to get through the cover, thereby safeguarding your truck bed and its contents. The cover automatically secures as the locking levers at the tailgate engage. These sturdy levers have reinforced gussets that give them added strength and durability. And they will never need adjustment.
To roll up the cover, unlatch the rear slat by dropping the tailgate and pulling either of the 2 release cords located along the bottom corners of the slat's housing. Either cord will release both of the latches so that you can raise the rear slat. When the latches are disengaged, the teeth roll back into the frame rails, releasing the sides of the cover so that you can easily roll it up. Just fold the rear slat over and roll up the cover the rest of the way.
Then secure the tonneau behind the cab with built-in nylon straps and sturdy plastic buckles. These straps help to keep the bundled tonneau from contacting your cab while you drive. And 4 rubber bumpers act as cushioned barriers between the cover and your truck cab.
The Revolver X2's rugged aluminum and vinyl construction makes it an ideal match for your truck, no matter what you do while at work or play. This cover is strong enough to hold up to 400 lbs of evenly distributed weight when it's rolled out. The 1/4" thick, aircraft-grade aluminum slats are covered with a textured black vinyl skin for superior resistance to impacts, UV rays, and weather. This skin is what gives the tonneau its soft, sleek look. While the Revolver X2 may look like a soft cover, its aluminum skeleton provides exceptional security because it cannot be cut through in the same way that a standard soft vinyl cover can be.
Felt strips on the underside of the tonneau help to keep the slats from scuffing the vinyl top as you roll up the cover. The soft felt also shields your hands when the cover has gotten hot or cold. And rubber strips overlay your truck's side rails, cab rail, and tailgate, creating a seal that helps to conceal any gaps and works to prevent water from seeping in.
Installing the Revolver X2 is simple. All you need is a wrench, and you don't have to do any drilling. The tonneau's frame rails clamp to the inside of your truck bed side rails to create a base for the cover. The included bolts secure the front hinge rail to the frame rails at the cab.
Slotted brackets at the ends of the tonneau side rails allow the bolts to shift in case you need to adjust the cover to achieve a snug fit. These brackets ensure proper alignment of the tonneau frame on your truck bed side rails. This eliminates trial and error in installing your rails - you won't have to put them on and then take them off again to get the correct fit. Pre-installed shims and spacers also help to ensure that the Revolver X2 rails are installed squarely on your truck bed.
California residents: click here
Looks great. Ease of operation is grea t.
Great cover! Arrived on time.
I have used this over a year now and it works perfect.
Easy easy to use and perform well
I’ve had this cover for over a year and have nothing but great things to say about it. It’s solid, well built, and kept whatever I’ve put in the bed dry.
Well,I do like the tonneau cover ,but, when rolled up to to tow a 5th wheel where the rolled cover sits stowed it has damaged the cover by punching thru the material. I suppose you don’t have a fix for this , like a wear strip that can be put over this for some protection .? With the weight of the rolled up cover in the stowed position for towing and the air and road vibration the cover moves just enough to wear thru the material , it would be good if you have a fix.
Fast delivery as usual form etrailer. Product looks great.
Tonneau cover installed without any problems. Directions are excellent.
This cover has been great with no problems whatsoever after one year. I highly recommend it and would certainly buy it again, but I think it will last a long time so, it will probably not be until my next truck.
I love this roll up cover. Only takes up an extra inch of space.
I still like the top. However, if you are in an area that gets a lot of rain, plan on either it being wet inside the box or plan on doing some extra effort to seal out the rain water.
Great product! The only issue I have is the straps that secure the cover when rolled up. If they were a couple of inches longer, it would be easier to get my fat little fingers in there.
As always, outstanding customer service. Had to call before buying with weird question about compatibility with equipment management systems. They took time to find an obscure reference confirming it would fit.
Pretty straightforward to install, looks great. Anticipating it to function as designed. Super good video preview to know what you have picked and how it compares to other styles
Great product. Had the same type of BAK rolling cover on my old truck. Looks good and functional. I like that it allows me to use the whole bed. Great service from Etrailer.com.
Love this cover. It gives me the freedom of an open truck bed and the security of a locked trunk. It's been nice keeping my fly fishing gear secured in the back and ready to use at a moments notice.
I have had this cover for one year and I would not buy it again. I read the reviews about how terrible this design is in climates that has freezing temps, but I live in New Orleans so freezing rain and snow was not a concern.
Turns out it’s not just cold weather and ice that ruins this, so doesn’t the sun and heat. The vinyl cover that you see when the cover is down is glued to a bunch of aluminum pieces and this design allows it to roll up and down. When the sun heats up the vinyl the glue separates from the aluminum sections and the cover will not roll up or down.
Don’t get me wrong, the concept is great, but the companies execution is off. I think I bought the second iteration and if I were you I would wait until the 6th or 7th version. They are far from getting this design right.
The only issue I've experienced with this cover that I was not pleased with was it blew up from one corner during a very strong crosswind and several of the plastic rail clips broke. I consider it an anomaly since its never happened again. BAK sent me replacement parts at no cost. The repair was simple.
On the positive side the cover gives you additional security from theft due to its construction. It's expensive but I feel worth the money, especially when protection of valuable cargo is needed.
The felt-like lining that lies on underside of cover (and acts as cushion for rolling?) had bad glue job. This material came off in under 1 year. Appears that the glue was not meant for hot weather, as it came off in summer heat. Disappointed. Mfg website does not provide instructions on what glue to use to reattach, so had to experiment to find glue that would work to reattach. Perhaps in future they should use mechanical attachment instead of glue method...
This is the best tonneau cover I have ever owned .And I have had several different type .It has some small leaks but the only one that I had that didn’t covered the bed rails.
Love my BAK Tonneau cover. If there was one thing I've had an issue with is in the winter the track can freeze down and stop you from opening the cover. But other then that I am very happy with it.
This BAK RevolverX2 tonneau cover is a high quality product that has performed well on my GMC Sierra 2500HD, it keeps my cargo safe, relatively dry and I save fuel. what more could ask for in a product.
I purchased this cover about a year ago for my 2019 Nissan Titan. I was happy with the appearance, it makes the truck stand out like no other. I can store things in the back, like luggage when traveling and it is secured and it will not leak. The cover itself is pretty sturdy, I have sit about 100 Lbs. on it and it doesn't bow in. I have the leather edition and it is easy to clean. It looks new even after a year, But maintenance is required to keep it looking good. Just keeping it clean and leather conditioner keeps it looking spectacular.
I have found the cover easy to install. It still works fine 1 year later. It is easy to roll up using one hand. The only problem I experienced so far is occasinal failure of the wire to release the cover on the driver side of the cover when operatred from the tailgate on the passenger side. Its otherwise been a perfect product keeping even the worst rain and snow out of the back of my pickup.
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.