Welcome back Michael. The 7-Way Vehicle Power Adapter #FR87PR takes the vehicle’s PWM/insufficient running-light signal and provides a steady 12V supply so Furrion cameras can operate properly. The tow vehicle lights still need to be powered on to…
Hey David, you can replace your Coleman Mach 15 with the Coleman Mach Everest part #CM35MR and use the same wiring that's behind the walls. Everything else would need to be swapped out but the wiring can be reused. We only have the Everest in the…
Hi Toby, At this time, Coleman Mach has not announced a heat pump version of the Mach Everest RV Air Conditioner #CM63MR. The current Mach Everest is marketed as a cooling-only, variable-speed air conditioner, and I have not seen any official…
Welcome back Ryan and thanks for the information. The LaSalle Bristol Cable-Actuated RV Waste Valve item #34466N4BB72GM is going to be the correct one for your 2020 Grand Design 390RK. Unfortunately, the valve body can not be purchased separately.…
Hello Kevin, Sorry for the delay, I had to reach out to Roadmaster on this one. Great question, I get what you’re saying about not wanting threads in the stack-up. Short answer, yes, the Replacement Car-Side Installation Hardware for Roadmaster Tow…
Hi Ashley! Yes, we do. If you're looking for the PopStep kit that includes the pieces between the steps, you'll want the PopStep, GapGuards, and NightLine Kit for MORryde StepAbove 3 Step, 19-1/2 Inch Treads, Part #PS63UR. This kit includes…
Hey Kyle! That is correct. The Coleman-Mach Mach-C Everest has variable-speed cooling and an inverter-driven compressor. However, the Mach-C Everest uses a traditional wall thermostat instead of a remote control. It also works with both ducted and…
We sure do Bruce and welcome back! The Curt V-5 S0700U-R2 receiver is our Ball Mount item #D-26. The Curt item #D-26 is a 2" ball mount with a 7,500 lbs towing capacity. It provides a 3/4" rise, a 2" drop, and has a 1" diameter…
Hey Jason! I'm guessing you have the 12" long shank right now which is the standard. For a longer shank that fits a 2-1/2" receiver you can use the Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 16" Long - 7" Rise,…
Hey Darren! Do you know the exact model of your Parallax 7300? There are different ratings and styles within the 7300 series. WFCO with the auto detect is a good option, but you're going to need to match it up with what you have now. You can…
Hi Glenn, I was able to pull a few specs from your Dexter axle number, it looks like it is a 3.5K EZ-lube axle with 5 on 4 1/2 bolt pattern and a 2 3/8" diameter axle tube. I wasn't able to determine the hub face or spring center measurement…
What is your current tire size? The only tire size I saw mentioned online for a Flagstaff 176LTD is ST145-12 (also commonly referred to as 145/80-12). We do offer that size in a radial as part #AM10130 which is a load range D with a 1220 lb per…
Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair.
Get solid footing and cut down tracked-in grit with black, 22 inch wide step covers. They install in minutes and help pets handle the steps; some options use spring attachments, and you can offset or trim for a cleaner fit. If your steps are 24" wide, a 22 inch cover will leave the edges exposed.
Yes, they make steps easier on dogs' feet and help reduce slipperiness when wet. They also cut down on tracked-in debris. Fit them snug and check that each cover is centered so paws have full contact on the tread.
They secure with springs and install with clear instructions. If the step has obstructions, offset the cover to the side you actually use. If you notice any shifting, re-center it and squeeze the spring ends tighter. In some cases, trimming or notching the cover helps it fit and close more easily.
Look for a snug fit and rugged material—users report covers holding up well after a year. Springs can rust on some setups, so inspect them periodically and replace if needed; many have stayed looking and working great after a year. Re-tension the springs if you see movement to help the cover stay put.
Yes, if your steps are up to 24" wide and 8" to 11" deep. The covers themselves are 22" wide, so on a 24" step the edges will be exposed. Measure each step's width and depth, and note if they're curved or straight—these can fit both. For mixed-depth sets, match each cover to the step depth you have.
Curved Steps
Filters
