Welcome back Ryan and thanks for the information. The LaSalle Bristol Cable-Actuated RV Waste Valve item #34466N4BB72GM is going to be the correct one for your 2020 Grand Design 390RK. Unfortunately, the valve body can not be purchased separately.…
Hi Glenn, I was able to pull a few specs from your Dexter axle number, it looks like it is a 3.5K EZ-lube axle with 5 on 4 1/2 bolt pattern and a 2 3/8" diameter axle tube. I wasn't able to determine the hub face or spring center measurement…
Hey Bob, yes the PopStep for MORryde StepAbove #PS47UR that you referenced does come with 2 steps that are slightly shorter front to back and slightly longer one for the top to match the step sizes on the MORryde StepAbove fold down steps. Are the…
Hi Eric - yes, that’s completely normal. The Jay Feather Micro sits lower to the ground than many larger travel trailers, so a 2-step Lippert SolidStep setup is typical from the factory. Now just verify tread width before ordering so you don't…
What is your current tire size? The only tire size I saw mentioned online for a Flagstaff 176LTD is ST145-12 (also commonly referred to as 145/80-12). We do offer that size in a radial as part #AM10130 which is a load range D with a 1220 lb per…
Hey Patrick, to end up with two 3 inch diameter electric waste valves what you'd want is two of the LaSalle Bristol MotoDrain waste valve part #LSB42TR as we don't have a kit like what you referenced with both 3 inch sizes. Do you have a…
Hey Johnny! That definitely sounds like a PWM issue so the 12V PWM Filter for RV Backup Camera Systems #VGR64VR is the solution. This is a permanent installation on the trailer side so you don't have to worry about keeping track of an adapter…
Hey Steve, do you know what brand of RV steps you have? If they happen to be the MORryde StepAbove style of steps we have the boot scraper/brush part #MR49RV. Then for a telescoping hand rail we have the MORryde part #MR54BR.
The Kenda Karrier ST225/75R15 Radial Trailer Tire - Load Range E #AM10303 would work just fine to replace the Westlake ST235/75R15 tires currently on your trailer but will be about 1/2" narrower and shorter. The #AM10303 has a load rating of…
Unfortunately, it will not Brian but thanks for the picture. Our Replacement Fabric for etrailer Slide-Out Toppers has a different attachment method so it will not work with your Solera RV Slide-Out Awning item #LCV000177334. The only replacement…
Hey Wade, based on the dimension you listed the correct replacement awning kit would be the part #LCV000335015-362241 which is 21 feet between the center of the arms like you measured.
Hello again Gary, Great question. Based on your 2024 Chevy 2500 with the 8' bed and factory puck system, along with your Cougar 23MLE and Road Armor pivoting pin box, the best option I recommend is the B&W Companion OEM 5th Wheel Hitch for…
Snap-on covers add traction and cut the clang of metal steps. The pop step design presses over the tread lip, so installation takes minutes without drills, tape, or adhesive. Choose by measuring tread width edge to edge and match your 2-step or 3-step setup, with versions to fit a deeper top step.
Yes, there are Pop Step kits for MORryde StepAbove. Measure the tread width and note your step count; these kits include a deeper top-step cover to match the StepAbove layout. If a cover won't stay on, confirm you selected the MORryde-specific kit and that you measured the tread, not the door or frame.
No tools are needed. Each cover is molded to hook around the bottom lip of the tread—line it up and press so it wraps underneath and grips. No drills or adhesive are used. If a cover doesn't stay on, recheck tread width, confirm you have the right step family (Lippert or MORryde), and make sure the bottom groove is fully seated.
Match the Pop Step kit to your tread width and step count. Measure across the flat metal tread (edge to edge) and confirm if you have 2-step or 3-step, and whether the top tread is deeper. Kits molded for 20 inch or about 24 inch treads snap on; 26 inch treads can work but may be a bit short on each side. A deeper top-step cover is available for setups with a deeper top tread.
Yes, Pop Step provides a textured surface for grip and can quiet the feel going up and down. The flexible PVC snaps on instead of using adhesive, so there's no glue to soften in heat or soak up water. If you feel movement, press the cover fully around the tread lip and verify the width match.
Lippert Steps
MORryde Steps
RV Step Covers Parts or Accessories
Filters
