Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…
Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…
That is correct Trevor! The Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel item #PD4590K18LS8 would be the correct replacement. This is a 90-amp 2-in-1 AC/DC distribution panel and converter charger that…
Hello Paul, There is one thing I like to have when I'm out enjoying the wilderness, and that's a toilet that feels like I'm at home. Well, I found just that for you. Since you're replacing the Dometic 300 in your 2021 Winnebago Minnie…
Hey Arlen, welcome back! For a hitch I recommend the Curt Adjustable Width Trailer Hitch #13703. This Class III hitch fits 22" to 72" wide trailer frames and can be bolted or welded on for installation. It has a max tongue weight of 350 lbs…
Your current microwave has the dimensions of 29-15/16 W x 16-7/16 H x 15-3/8 D which is almost identical to the Furrion part #FMCM15SS which we know works really well and is reliable so it would be a really great and easy solution.
Hey Eumir, the 9610007991 Dometic Connect Essential RV Thermostat RV-C #DMC79JF does not have the ability to control the two heat sources independently. It can control both but it does not have ability to pick between either.
Hey Tim, I checked out your Predator 5000 generator and it does use a quick connect propane connector like what the part #CAM57629 provides so yes this would work. How do you like the Predator generator?
Hey Robert & Carol, That part number comes back to a custom order piece. Is this the channel on the side of your RV that the fabric from your awning slots into, like part #LC715216? If you'd like to email me some pictures I'd be happy to…
Hello Kenneth, Thanks for writing in. I don’t have a database that shows exactly what was installed in every camper, but based on my research, your 2020 Transcend Xplor 243BH most commonly came with a 6-gallon Dometic (Atwood-style) water heater.…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
The phone operator was very helpful and made my purchase easy. I will keep this website handy.
Harold
Gillsville, GA
Kwikee RV Door Parts for easy replacements
Get straightforward swaps for worn latches and T-style holders with Kwikee RV door parts. Check your hole spacing—options noted at 1-1/8 in horizontal and 2-7/16 in or 2-1/2 in vertical—to line up for a direct fit, otherwise slight adjustments may be needed. Some holders are plastic, and versions with a rubber bumper will keep your door from hitting your RV.
Not always. Several installs noted the holder did not include replacement screws or putty. Plan to have mounting screws that match your existing holes and a suitable putty or sealant ready. Test-fit the keeper and latch, then seal and fasten to prevent leaks.
Measure your current mount first. A Kwikee T-style was measured at 1-1/8" horizontal on center and 2-7/16" vertical. If yours is about 1" x 2-1/8", expect a small difference. Some installs reported slightly angled screws or minor adjustment when holes didn't line up exactly. Mark and dry-fit before drilling to confirm alignment.
Kwikee T-style door holders are constructed from plastic. Some versions include a rubber bumper to help keep the door from hitting your RV. If your rig sees a lot of hot sun, check the material details and consider how plastic exposure and heat might affect longevity over time.
It can be, but verify measurements. Some were perfect hole-for-hole replacements; others saw small spacing differences. Compare your spacing, like 1" x 2-1/8", to a Kwikee pattern such as 1-1/8" x 2-1/2". If it's close, minor adjustments or re-drilling may be needed. Check latch style (T vs alternate shapes) to match your keeper.
Filters
