Hey John! Yes, the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-440-2-G-EZ-1K looks to be exactly what you're needing! What boat trailer do you have?
Hey Peter! Hopefully nobody was hurt, including your camper. Since you have a trigger latch I would add a lock like the InfiniteRule Trailer Coupler Lock #IR58FR. This will keep it secure while you're hooked up to the ball mount on your vehicle…
For an air bag kit that fits your 2014 Chevy Silverado 1500 towing a fifth wheel trailer I would recommend the #AL57204 for if you have a short bed truck or the part #AL88211 for if you have an 8 foot bed. Now if you were to ask me what suspension…
Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…
Hey Tom, thanks for the picture and all the information! The 25-1/4" Long etrailer Rust-Resistant 3-Leaf Double Eye Spring item #e93SR, you were looking at will probably work just fine but I still recommend measuring to confirm. Leaf springs…
Hello Brad, thanks for reaching out. For a compressor system to go with your Air Lift LoadLifter 5000 air bags I recommend the following: - Air Lift WirelessONE Suspension System for Air Helper Springs - Remote - Bluetooth - EZ Mount #AL77DQ This…
When you mention locking collar, I am led to believe that you might be describing a hammer blow-type coupler, like our part #BD028288. This type of coupler has a collar that would slide up, securing the jaws of the coupler in place over the trailer…
When you tighten the two nuts on the studs of the Trailer Spare Tire Carrier #DL22128 you were looking at, it will squeeze the tire against the frame which will keep it secure and won't allow it to slide back and forth. I wouldn't hesitate to…
Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?
Hello Rick, The RV air conditioner refrigerant went from the R410a to the R32 this year. The new R32 is much more efficient making it a win-win for the environment and the consumer. With every good news, there tends to be some bad news. The new R32…
You could use a BoatBuckle Pro Series Kwik-Lok Bow Tie-Down #IMF18741. On the trailer side you would want to run the loop end of the strap and then use the hook end to attach to the bow eye on your boat.
I went out to the warehouse and pulled a BoatBuckle Pro Series Kwik-Lok Gunwale Tie-Down Strap #IMF17634 to measure it for you. Both the fixed end and the ratcheting end of the straps are about 5 feet long (just the strap part. From the end of the…
Hey John! Yes, the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-440-2-G-EZ-1K looks to be exactly what you're needing! What boat trailer do you have?
Hey Peter! Hopefully nobody was hurt, including your camper. Since you have a trigger latch I would add a lock like the InfiniteRule Trailer Coupler Lock #IR58FR. This will keep it secure while you're hooked up to the ball mount on your vehicle…
For an air bag kit that fits your 2014 Chevy Silverado 1500 towing a fifth wheel trailer I would recommend the #AL57204 for if you have a short bed truck or the part #AL88211 for if you have an 8 foot bed. Now if you were to ask me what suspension…
Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…
Hey Tom, thanks for the picture and all the information! The 25-1/4" Long etrailer Rust-Resistant 3-Leaf Double Eye Spring item #e93SR, you were looking at will probably work just fine but I still recommend measuring to confirm. Leaf springs…
Hello Brad, thanks for reaching out. For a compressor system to go with your Air Lift LoadLifter 5000 air bags I recommend the following: - Air Lift WirelessONE Suspension System for Air Helper Springs - Remote - Bluetooth - EZ Mount #AL77DQ This…
When you mention locking collar, I am led to believe that you might be describing a hammer blow-type coupler, like our part #BD028288. This type of coupler has a collar that would slide up, securing the jaws of the coupler in place over the trailer…
When you tighten the two nuts on the studs of the Trailer Spare Tire Carrier #DL22128 you were looking at, it will squeeze the tire against the frame which will keep it secure and won't allow it to slide back and forth. I wouldn't hesitate to…
Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?
Hello Rick, The RV air conditioner refrigerant went from the R410a to the R32 this year. The new R32 is much more efficient making it a win-win for the environment and the consumer. With every good news, there tends to be some bad news. The new R32…
You could use a BoatBuckle Pro Series Kwik-Lok Bow Tie-Down #IMF18741. On the trailer side you would want to run the loop end of the strap and then use the hook end to attach to the bow eye on your boat.
I went out to the warehouse and pulled a BoatBuckle Pro Series Kwik-Lok Gunwale Tie-Down Strap #IMF17634 to measure it for you. Both the fixed end and the ratcheting end of the straps are about 5 feet long (just the strap part. From the end of the…
Inflatable Boat Bumpers: Perfect for Every Adventure
Inflatable boat bumpers are a versatile and durable choice for protecting your boat. Easy to install and store, they offer excellent protection against docks and other boats. Ideal for both casual and frequent boaters, these bumpers ensure your vessel sta
Yes, inflatable bumpers are incredibly easy to install and store. They can be quickly inflated and deflated, making them convenient for storage when not in use. Their lightweight nature also makes them easy to handle, perfect for boaters who need flexibility.
Yes, inflatable bumpers can be customized. Many boaters personalize them with boat names or logos, adding a unique touch. This customization does not affect their performance, allowing you to enjoy both style and functionality on the water.
Inflatable bumpers fit well in most fender racks, including popular models like the Taylor made fender rack. Their flexible design allows them to conform to various rack sizes, ensuring a snug fit and easy access when needed.
Inflatable bumpers perform excellently in rough conditions. They provide robust protection against impacts, even during storms or when docked in busy areas. Their ability to absorb shock helps keep your boat safe and secure, making them a trusted choice for many boaters.
Inflatable boat bumpers are known for their durability. They withstand frequent contact with docks and other boats without leaving marks. Many find them to be a reliable choice even in busy or rough waters, providing ample protection and maintaining their shape over time.
Filters
