We offer 4 Class III hitches that are a confirmed fit for your 2015 Ford Edge Sport: • etrailer brand Class III hitch, part #e36RR • Curt Class III, part #C78KR • Curt Class III, part #C13234 • Draw-Tite Class III, part #75234 I'd eliminate the…
Hey Daniel, welcome back! You do not have to strip the wires before installing them on the TowSmart 4-Way Flat Connector Rapid Repair Trailer Wiring Kit item #TS68QR. The 4-way connectors have sharp metal prongs that slice the wiring insulation or…
The best I can do, without knowing your exact golf cart model, is show you how to calculate the maximum weight you can carry on your 2022 Ford F-250 when using the Mad-Ramps Pivoting Ramp System for ATV/UTV Ramps - 1,400-lbs - 2" Hitch, part…
There is a potential solution for you but the Arched Loading Ramp Set #288-07432-2 you referenced would not work with your 2017 GMC Sierra 2500HD with a 39-1/2 inch bed height. Instead, you may be able to use the Erickson Arched, Aluminum Loading…
To replace the OEM ramp for your 2002 Triton Elite, I recommend the Loading Ramp Set - Steel - 48" Long x 11" Wide x 1-1/2" Thick - 1,600 lbs - Qty 2 #288-07474-2 or the Aluminum Car Hauler Ramp Set - 48" x 14-1/2" - 6,000…
Hey Greg! Where did your Stromberg Carlson Base Pad Extreme #SC53VR crack? The Andersen Trailer Jack Block #AN39VR is a good alternative. It has the same 6,000 lb capacity and the design is a little more basic/straightforward which makes it less…
The MORryde Sliding Tray for RV Cargo Compartment #MR44FR has 1.57" of clearance before the tray starts. If you are needing more clearance than that the MORryde Sliding Tray Height Adjustment Kit #MR34VR will allow you to raise the tray…
I've attached the wiring diagram for you to check out, but it sounds like the compressor for your #AL57289 is not getting power. The wiring harness has an ignition wire which if not connected to an ignition source, will not wake up the compressor…
It won't be an issue. Since the combined weight of the #288-07452-2 is 1500 pounds, the ramps are designed to withstand the 1,450 pounds of your mower. However, if you are worried about it, you can always go with the #288-07474-2 which has a…
Hey Chris, the good news is yes, the Roadmaster Direct-Connect Base Plate Kit #RM-524431-5 that you have for your 2020 Ford F-150 Raptor will also work for your 2025 Ford F-150 Raptor. As of right now it does not look like we have an install kit for…
Hey Michael! The etrailer Electric Trailer Jack w/ 7-Way #e74GV you were looking at will definitely have enough lift for your Coleman 13R. This is a great option if you just want to power the jack off the 7-way on your vehicle instead of running it…
Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Go with 77 inch long ramps when you want a gentler approach for low-clearance gear like mowers or snowblowers, and steady footing for your ATV. Strap the ramps to your vehicle or trailer to keep them from shifting while you load. If you're using a tri-fold style, set them up in the intended direction, not sideways, so the hinges aren't taking the load.
Yes, 77" length helps with lower clearance compared to shorter ramps. A large, continuous loading surface can make it easier since you don't have to align separate tracks. If you want a gentler approach, a 90" option reduces the angle more than 77".
No. Sideways use leaves the lower and middle brackets unsupported and puts the load on tri-fold hinges that are not rated to carry it. Keep the ramp oriented as designed and distribute weight across the panels. Follow the usage instructions rather than improvised mounting to help avoid failures.
Secure the ramps to the bed with the included straps to help prevent kick out during loading. Folding ramps often have locking devices when closed; check the side locks since they can rattle loose when folded. If hauling ramps on the side of a trailer, mount and strap them so they stay out of the way.
It can if the ramp is rated 1,500 lbs with weight evenly distributed. That equals 750 lbs per side; 970 lbs is about 485 lbs per side, and a 200 lb driver on one side makes about 685 lbs on that side. Stay within ratings and load smoothly; if you're near limits, consider longer or higher-capacity ramps.
Filters
