How Much Does the Flint Hill Goods Arched Ramp Set Weigh

Question

Question:

how much do these ramps weigh?

asked by: Jason

0

Expert Reply:

Hey Jason,

The individual ramps from the Flint Hill Goods Arched Ramp Set # FHG83ZR weigh in at 14.5 lbs so combined you're looking at 29 lbs.

expert reply by: Jon G

0

Jon G.

11/17/2025

Hey Jason, how did the weight of the Flint Hill Goods ramps work out for your setup? Knowing if they were easy to handle could help others choosing a similar ramp set.

Answer 1

Hey Jeremiah, The Flint Hill Goods Arched Ramp Set #FHG83ZR can be used with a max height of 25". If you need something that works with more height then you'll need the Arched Loading Ramp Set #288-07432-2 which can work with a 35" max…

view full answer...

Answer 2

Hey Taylor, The 3,000 lb weight rating of the Flint Hill Goods Arched Ramp Set #FHG83ZR is for both ramp combined. Each ramp has an individual weight rating of 1,500 lbs so combined it's 3,000 lbs altogether.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

How Much Does the Flint Hill Goods Arched Ramp Set Weigh

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching